[Other] SpaceClaim Line Body

Andrea159357 · September 3, 2019, 12:25

Hello,
In design modeler is possible to convert line to solid body, is there a possibility to do so in Spaceclaim?

I would like to draw a spline in a single volume to have a sizing control over the line.
The alternative is to split the volume and i don't like it so much.

Thanks

Andrea159357 · September 3, 2019, 17:38

Does someone have the answer?

Gweher · October 4, 2019, 13:46

Hi Andrea,

Not sure about what you want to achieve... What do you mean by "In design modeler is possible to convert line to solid body" ?

If you're looking for beam elements with Spaceclaim, you can simply add a profile to your line/spline under > Prepare > Profile > Add profile.

Have fun

Andrea159357 · October 9, 2019, 05:34

Thanks Gweher for your reply. In ICEM i can import line body just to have small elements in that precise line.
I'm simulating jet flow of a plume in a sea current. I ran a coarse mesh just to undestand the trajectory of the plume in the sea; i draw it as a line in spaceclaim and now i would like to import the geo in ansys meshing, though i can import just solid and surfaces.
In ICEM i can import line and refine just that line, though time for tetra mesh construction is quit large and, personally, i prefer tetra mesh made with ansys meshing.

Gweher · October 14, 2019, 06:55

Hi Andrea,

Well in your case if you want to mesh everything with ANSYS meshing you need to change the import resolution of the system.

In workbench go under Tool > Properties. Then select the geometry cell and on the right you'll have a panel. Go to Advanced Geometry Option > Mixed import resolution > Select the appropriate.

This should do the trick.

Have fun

pigei · April 19, 2021, 09:39

Has anybody found a way to draw line in spaceclaim and made them result in line bodies?

This is allowed in design modeler.

I would like to do that in order to definy a body of influence towards a direction (the direction of the line) in the mesh.

September 3, 2019, 12:25	SpaceClaim Line Body	#1
Andrea159357 Member Andrea Join Date: Mar 2018 Posts: 62 Rep Power: 8	Hello, In design modeler is possible to convert line to solid body, is there a possibility to do so in Spaceclaim? I would like to draw a spline in a single volume to have a sizing control over the line. The alternative is to split the volume and i don't like it so much. Thanks

October 9, 2019, 05:34		#4
Andrea159357 Member Andrea Join Date: Mar 2018 Posts: 62 Rep Power: 8	Thanks Gweher for your reply. In ICEM i can import line body just to have small elements in that precise line. I'm simulating jet flow of a plume in a sea current. I ran a coarse mesh just to undestand the trajectory of the plume in the sea; i draw it as a line in spaceclaim and now i would like to import the geo in ansys meshing, though i can import just solid and surfaces. In ICEM i can import line and refine just that line, though time for tetra mesh construction is quit large and, personally, i prefer tetra mesh made with ansys meshing. Last edited by Andrea159357; October 9, 2019 at 08:36.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[Gmsh] 3D Mesh conversion from gmsh-2.5.0 to OpenFOAM	Ancioi	OpenFOAM Meshing & Mesh Conversion	17	January 8, 2019 23:50
[Gmsh] Problem with Gmsh	nishant_hull	OpenFOAM Meshing & Mesh Conversion	23	August 5, 2015 02:09
Derivative of velocity and mean velocity	hiuluom	OpenFOAM Post-Processing	1	May 29, 2015 23:42
[blockMesh] error message with modeling a cube with a hold at the center	hsingtzu	OpenFOAM Meshing & Mesh Conversion	2	March 14, 2012 09:56
Problems of Duns Codes!	Martin J	Main CFD Forum	8	August 14, 2003 23:19

September 3, 2019, 17:38		#2
Andrea159357 Member Andrea Join Date: Mar 2018 Posts: 62 Rep Power: 8	Does someone have the answer?

October 4, 2019, 13:46		#3
Gweher Senior Member Gwenael H. Join Date: Mar 2011 Location: Switzerland Posts: 392 Rep Power: 20	Hi Andrea, Not sure about what you want to achieve... What do you mean by "In design modeler is possible to convert line to solid body" ? If you're looking for beam elements with Spaceclaim, you can simply add a profile to your line/spline under > Prepare > Profile > Add profile. Have fun

October 14, 2019, 06:55		#5
Gweher Senior Member Gwenael H. Join Date: Mar 2011 Location: Switzerland Posts: 392 Rep Power: 20	Hi Andrea, Well in your case if you want to mesh everything with ANSYS meshing you need to change the import resolution of the system. In workbench go under Tool > Properties. Then select the geometry cell and on the right you'll have a panel. Go to Advanced Geometry Option > Mixed import resolution > Select the appropriate. This should do the trick. Have fun

April 19, 2021, 09:39		#6
pigei New Member Paolo T. Join Date: Jul 2019 Posts: 15 Rep Power: 6	Has anybody found a way to draw line in spaceclaim and made them result in line bodies? This is allowed in design modeler. I would like to do that in order to definy a body of influence towards a direction (the direction of the line) in the mesh.