CFD Online Discussion Forums

CFD Online Discussion Forums (https://www.cfd-online.com/Forums/)
-   ANSYS Meshing & Geometry (https://www.cfd-online.com/Forums/ansys-meshing/)
-   -   meshing of turbine blade (https://www.cfd-online.com/Forums/ansys-meshing/64973-meshing-turbine-blade.html)

jayaero May 30, 2009 07:23

meshing of turbine blade
 
hi,
I want to learn turbo machines analysis in GAMBIT and Fluent.....
Anyone who have experience of CFD please help me....
please give me if u have any tutorials (apart from given within softwares)....
I am working for my masters thesis on effect of stagger angle on turbine blade cascade.
Thank you.

sivarama1 May 30, 2009 07:33

tutorials of turbine blades
 
HI,
Give me your mail ID i should send,actually i have pdf format
All the best.

Far May 30, 2009 14:10

There are two ways of doing this.
1. using Template for turbomachinery i.e. G turbo. This is the easiest way with minimal user input
2. Manual method

Now tell me whichmethod you like.

jayaero May 30, 2009 14:45

@ sivaramakrihnaiah
 
@ sivaramakrihnaiah

Thanks for reply.
my e mail id is jaydeeptrivedi03ae47@yahoo.com

jayaero May 30, 2009 14:50

@ Far
 
Thanks for reply.
Does G turbo stands for Turbo tool in gambit.
I would first like to go for easy method as I have less little experience in turbo meshing.

Thank You.

Far May 30, 2009 15:16

You just have to convert the IGES file into turbo format i.e .tur . and then press some buttons in gambit. your file of turbine/compressor simulation is ready.
That is all you need in gambit and then run solution in fluent

jayaero May 31, 2009 02:07

@ Far
 
Thanks for reply.

I have done gambit tutorials related to turbo tool but since same tuto is not in fluent i am having problems...
I dont know which boundary conditions r to be applied.
I need some tutorial of turbo which guides through both gambit and fluent.
some research papers r there but most of them requires subscription.
do u have any tuto apart frm already given in software?

Far May 31, 2009 07:33

you need following boundary condtions
1. Total pressure , total temprature, flow inlet angles at inlet
2. Static pressure at outlet corresponding to required mass flow rate and you need to turn on the radial equilibrium option
3. Fluid speed equal to your rpm (set the rpm as low value and then gradualy increase to required level.
4. Casing is stationary
5. periodic conditions for periodic surfaces

Flow setting
1. Initially 1st order and courant number 1
2. Flow solver coupled implicit (also named as density based in fluent 6.3 and latter)
3. initialize from inlet values

Turbulence model
1. K epsilon
2. SA (I have worked extensively with SA and found to be very accurate)
3. SST

anat_sri June 10, 2009 05:38

to sivaramakrihnaiah
hi, I need too please
my email is iamnotslave@hotmail.com

zhh0910 September 3, 2009 11:07

to sivaramakrihnaiah
hi, I need too please
my email is zhh091088@126.com:)

sivarama1 September 3, 2009 11:22

hi what you want

zhh0910 September 3, 2009 11:44

the pdf that I can learn how to mesh turbo machines

Pat October 29, 2009 14:39

hallo
please may i've got the pdf my mail ist assogbapat@yahoo.fr
thank you.

holyo November 9, 2009 12:39

Hello sivaramakrihnaiah, could you send me the pdf? My e-mail: xenxoc@gmail.com
I´m going to make a windturbine meshing and I need learn about it.

Thank you.

teguhtf November 9, 2009 22:49

@ sivaramakrihnaiah
Can you send me the pdf?? I need it. Thxs
here is my email: huget_teguh@ymail.com

teguhtf

Almohammadi November 10, 2009 23:02

Could you please send me the file or any one who recived it.

doctorkms@hotmail.com

Thanks

sivarama1 November 13, 2009 05:32

Turbine Tutorial
 
Hi all,
I am sending link here download,


http://www.4shared.com/file/15125741...ade_fuent.html

Pat November 14, 2009 15:40

think you for the file

Alberto1987 November 22, 2009 23:48

I have to simulate something like this for the University and it can be useful for me.

Thanks in advice

lopezflorenciano@gmail.com

sivarama1 November 22, 2009 23:55

welcome,
All the best for your bright future.
Are you from

Alberto1987 November 23, 2009 01:44

Thank you
I'm from Spain

sivarama1 November 23, 2009 01:47

I AM INDIAN,YOU HAVE DOUBTS,YOU COME ONLINE,
I AM SIMUALTING Tesla Turbine.
My skype ID:sivaramakrishnaiah1
My google talk ID:malayathisiva@gmail.com

Alberto1987 November 23, 2009 13:09

Thank you very much again

I add you as soon as I find issues, if you need something, i`ll do my best to help you

Edward! May 26, 2010 20:55

Thanks a lot sivaramakrihnaiah

dresden November 22, 2010 10:00

hi.
sivarama1
sivaramakrishnaiah

i was not able to download the tutorial from the given link,can u plz send it on my email id.
kartik.iitr@gmail.com
I will be thankful to you.

ANikzad July 25, 2014 10:52

please send for me too,thanks dear .
arashnikzad@ut.ac.ir


All times are GMT -4. The time now is 06:28.