[ICEM] Meshing Problem, overlap.

vdrx84 · January 30, 2013, 20:51

I am using ICEM CFD for a project I have acquired from a previous student and have been given a mesh that is representative of a blade inside a cascade. In the link below you can see how the mesh unfortunately fails. At the right hand side of the trailing edge the mesh overlaps itself. Also, to some extent the quality on the left hand side is rather poor. I am new to using ICEM CFD and I'm failing to understand where the mesh is going wrong. Any help or thoughts on possible issues with the mesh would be really welcome, thanks.

http://imageshack.us/f/706/screenshot1af.png/

Error messages:

bad params in create_edge_pars

and

error meshing edge (long list of edges here)

vdrx84 · January 30, 2013, 21:45

It seems that if i perform mesh refinement on that specific block then the overlapping disappears. I guess that suggests that the volume it is trying to mesh on is too narrow and it cannot do it so it just crashes and overlaps the mesh, is that a correct assumption?

Far · January 30, 2013, 22:40

I cannot see any overlapping in attached pic...

jeevankumarb · January 31, 2013, 01:32

It seems like just cure association issue. try to correct the curve association for the blade.

vdrx84 · February 3, 2013, 19:03

sorry for the late response, been rather busy these last few days. Thanks for the replies though. I have been looking through the replay script and haven't found the problem yet. I am creating another script from scratch and will be modifying the blade slightly so the error should come up in this process.

The script for creation of the curves for the blade is a bit of a mess I have to say, which is pretty annoying, but I can't complain too much as it has saved me a lot of work.

January 30, 2013, 20:51	Meshing Problem, overlap.	#1
vdrx84 New Member Jonathan Martin Join Date: Dec 2012 Posts: 3 Rep Power: 13	I am using ICEM CFD for a project I have acquired from a previous student and have been given a mesh that is representative of a blade inside a cascade. In the link below you can see how the mesh unfortunately fails. At the right hand side of the trailing edge the mesh overlaps itself. Also, to some extent the quality on the left hand side is rather poor. I am new to using ICEM CFD and I'm failing to understand where the mesh is going wrong. Any help or thoughts on possible issues with the mesh would be really welcome, thanks. http://imageshack.us/f/706/screenshot1af.png/ Error messages: bad params in create_edge_pars and error meshing edge (long list of edges here)

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Problem with querying the meshing database in CFX-Pre	ashtonJ	CFX	18	April 18, 2023 23:49
[Other] Hex meshing problem DM12	patrick	ANSYS Meshing & Geometry	7	January 9, 2015 07:21
[ICEM] Hexa meshing blocking problem	fergal	ANSYS Meshing & Geometry	0	June 28, 2011 10:01
Strange ANSYS Meshing 13.0 Problem	brunob	ANSYS Meshing & Geometry	3	June 21, 2011 20:03
Meshing problem in GAMBIT	Vidya Raja	FLUENT	0	May 20, 2006 23:31

January 30, 2013, 21:45		#2
vdrx84 New Member Jonathan Martin Join Date: Dec 2012 Posts: 3 Rep Power: 13	It seems that if i perform mesh refinement on that specific block then the overlapping disappears. I guess that suggests that the volume it is trying to mesh on is too narrow and it cannot do it so it just crashes and overlaps the mesh, is that a correct assumption?

January 30, 2013, 22:40		#3
Far Super Moderator Sijal Join Date: Mar 2009 Location: Islamabad Posts: 4,553 Blog Entries: 6 Rep Power: 54	I cannot see any overlapping in attached pic...

January 31, 2013, 01:32		#4
jeevankumarb Member jeevan kumar Join Date: Mar 2009 Posts: 88 Rep Power: 17	It seems like just cure association issue. try to correct the curve association for the blade.

February 3, 2013, 19:03		#5
vdrx84 New Member Jonathan Martin Join Date: Dec 2012 Posts: 3 Rep Power: 13	sorry for the late response, been rather busy these last few days. Thanks for the replies though. I have been looking through the replay script and haven't found the problem yet. I am creating another script from scratch and will be modifying the blade slightly so the error should come up in this process. The script for creation of the curves for the blade is a bit of a mess I have to say, which is pretty annoying, but I can't complain too much as it has saved me a lot of work.