[ICEM] Deleting unwanted edges

protea · February 1, 2012, 12:31

Hello everyone can anyone tell me how to delete the unwanted edges which are not necessary in geometry. For my geometry when i build topology, near the flaps its showing multiple edges(Blue curves), so untill i remove them i cannot go further go in meshing. So could any of u guys who already worked in this kind of situation please help me out in proceeding further and hoping for ur positive responses.

Regards
Dale

arjun3020 · February 2, 2012, 01:24

you can proceed with blue edges, there is no need to delete blue edges.

problem arises only if u have yellow edges.

protea · February 2, 2012, 01:31

thanks arjun for ur reply, yes indeed i proceeded further by ignoring them but i was not able to get the desired mesh in those particular regions. So the only other solution is to remove them first and go ahead. If u know the procedure how to do it, cud u plz share ur thoughts on this, it will be very much helpful to me. Thanks in advance.

Regards
Dale

arjun3020 · February 2, 2012, 01:45

i dint understand your main problem. i think that edges dint affect the mesh.
what type of mesh u did?
tell me more about geometry or send me your project at - arjun3020@gmail.com
i will check it.

February 1, 2012, 12:31	Deleting unwanted edges	#1
protea New Member dale Join Date: Nov 2011 Posts: 11 Rep Power: 14	Hello everyone can anyone tell me how to delete the unwanted edges which are not necessary in geometry. For my geometry when i build topology, near the flaps its showing multiple edges(Blue curves), so untill i remove them i cannot go further go in meshing. So could any of u guys who already worked in this kind of situation please help me out in proceeding further and hoping for ur positive responses. Regards Dale

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[snappyHexMesh] SnappyHexMesh for internal Flow	vishwa	OpenFOAM Meshing & Mesh Conversion	24	June 27, 2016 08:54
[snappyHexMesh] No layers in a small gap	bobburnquist	OpenFOAM Meshing & Mesh Conversion	6	August 26, 2015 09:38
[snappyHexMesh] snappyHexMesh won't work - zeros everywhere!	sc298	OpenFOAM Meshing & Mesh Conversion	2	March 27, 2011 21:11
[snappyHexMesh] external flow with snappyHexMesh	chelvistero	OpenFOAM Meshing & Mesh Conversion	11	January 15, 2010 19:43
Deleting Edges in Gambit	Alberto Schroth	FLUENT	4	May 31, 2000 14:15

February 2, 2012, 01:24		#2
arjun3020 Member arjun Join Date: Oct 2011 Location: Tokyo, JAPAN Posts: 66 Rep Power: 14	you can proceed with blue edges, there is no need to delete blue edges. problem arises only if u have yellow edges.

February 2, 2012, 01:31		#3
protea New Member dale Join Date: Nov 2011 Posts: 11 Rep Power: 14	thanks arjun for ur reply, yes indeed i proceeded further by ignoring them but i was not able to get the desired mesh in those particular regions. So the only other solution is to remove them first and go ahead. If u know the procedure how to do it, cud u plz share ur thoughts on this, it will be very much helpful to me. Thanks in advance. Regards Dale

February 2, 2012, 01:45		#4
arjun3020 Member arjun Join Date: Oct 2011 Location: Tokyo, JAPAN Posts: 66 Rep Power: 14	i dint understand your main problem. i think that edges dint affect the mesh. what type of mesh u did? tell me more about geometry or send me your project at - arjun3020@gmail.com i will check it.