|
[Sponsors] |
February 2, 2012, 10:48 |
Defining Zones
|
#1 |
New Member
Horst
Join Date: Jan 2012
Posts: 19
Rep Power: 14 |
Hello again,
I have a 2-D model diffuser which I want to define in 3 Zones so when I import them to fluent I could define flow/porosity/model there in each region. So Im still new to icem and tried everything but if I import it to fluent it stays as one geometry; all I can do is defining parts (inlets,outlets etc) but still no clue about zone. Anyone any idea? I looked in forum but most explanations confuse me because I cant seem to find it in my icem version (13.0 in my case). would be thankful for any help! |
|
February 4, 2012, 15:07 |
|
#2 |
Senior Member
Simon Pereira
Join Date: Mar 2009
Location: Ann Arbor, MI
Posts: 2,663
Blog Entries: 1
Rep Power: 47 |
Zones are determined by the Part...
If this were 3D you would need three material points, each in its own part so that the volume elements in each area would be in their own parts and would be seen as separate zones in Fluent. For 2D, you have shells instead of volume elements, and you control the part of the shells by controlling the part of the surface the parts are formed on... So, just put the surfaces in each area into separate parts. If you don't have surfaces because you are meshing from the perimeter curves only, I suggest you create surfaces from those curves... and then go put the surfaces in appropriate parts...
__________________
----------------------------------------- Please help guide development at ANSYS by filling in these surveys Public ANSYS ICEM CFD Users Survey This second one is more general (Gambit, TGrid and ANSYS Meshing users welcome)... CFD Online Users Survey |
|
February 6, 2012, 03:24 |
|
#3 |
New Member
Horst
Join Date: Jan 2012
Posts: 19
Rep Power: 14 |
Hello and thanks for your attention!
Seems what working for me is after meshing to break the connectivity of the geometry and making parts ( click on blocking and surfaces, so the whole mesh is in it ) of the zones, after that I can also define edges. |
|
February 6, 2012, 10:40 |
|
#4 |
Senior Member
Simon Pereira
Join Date: Mar 2009
Location: Ann Arbor, MI
Posts: 2,663
Blog Entries: 1
Rep Power: 47 |
Oh yes...
If you are using hexa blocking then, by default, edges between blocks in the same blocking material are color coded blue (cyan). These unprojected edges do not result in line elements. Simply putting the blocking into separate blocking materials will convert the edges between them into surface projected edges which will produce line elements... Best regards, Simon
__________________
----------------------------------------- Please help guide development at ANSYS by filling in these surveys Public ANSYS ICEM CFD Users Survey This second one is more general (Gambit, TGrid and ANSYS Meshing users welcome)... CFD Online Users Survey |
|
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Skipping Zones | 1337Hal | FLUENT | 1 | June 27, 2022 09:33 |
Defining dynamic zones for Define CG motion | aamer | Main CFD Forum | 0 | March 21, 2011 03:51 |
Defining Solid and Fluid zones in OpenFoam | foamcfd | OpenFOAM | 1 | December 17, 2009 06:02 |
Defining Solid Zones Not working | elmcmaster | FLUENT | 3 | May 22, 2009 07:14 |
defining zones ??? | Amal Jugdeo | Main CFD Forum | 0 | December 9, 1999 03:06 |