Creating named selection for a line sketch

amir00251 · July 30, 2012, 21:14

I am trying to model a simple rotating hallow cylinder, image below. I need to create a named selection for the central axis to be able to define rotation of axis when I am defining the rotational speed.

The problem is, I cannot create a named selection for the rotational axis in Geometry. I have sketched a line but you cannot create a named selection from a line.

I am new to Ansys, so would appreciate a help on this.

flotus1 · July 31, 2012, 04:22

Activate the selection of lines first.

amir00251 · July 31, 2012, 05:38

Hello, thanks for your reply. I still cannot select the center line to create a Named Selection after choosing line in selection type.

I can create Named selections for the surfaces of the body or for whole body but not for that center line. That center line is just a sketch... this should give a clue?

I read in another forum that if you want to create a Named Selection for a closed area inside a surface, you should extrude and change the option from add material to imprint ... something like this is required but I can not extrude a single line??

flotus1 · July 31, 2012, 05:49

I see...
You need the line only to define the axis of rotation? In your picture, the line coincides with an axis of the global coordinate system.
It should be possible to select this axis as the axis of rotation.

amir00251 · July 31, 2012, 06:07

Yes, I was thinkng that I can easily choose z axis as axis of rotation, but again there is not that possibility when I am defining rotatinal velocity ... would you please give details if this is possible.

flotus1 · July 31, 2012, 06:42

Actually it is not possible to choose the axis directly.
Instead, choose "define by" -> "components".
Now you can apply any rotation you like.
If you are not simulating structural mechanics, well sorry for assuming that.

amir00251 · July 31, 2012, 08:02

Thanks alot for your help, it did solve the problem. I think instead of Named Selection, I should look at how to define a vector...
or use component as you pointed out above...

July 30, 2012, 21:14	Creating named selection for a line sketch	#1
amir00251 New Member Amir Join Date: Sep 2011 Posts: 10 Rep Power: 14	I am trying to model a simple rotating hallow cylinder, image below. I need to create a named selection for the central axis to be able to define rotation of axis when I am defining the rotational speed. The problem is, I cannot create a named selection for the rotational axis in Geometry. I have sketched a line but you cannot create a named selection from a line. I am new to Ansys, so would appreciate a help on this.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[Other] mesh airfoil NACA0012	anand_30	OpenFOAM Meshing & Mesh Conversion	13	March 7, 2022 17:22
[Gmsh] Problem with Gmsh	nishant_hull	OpenFOAM Meshing & Mesh Conversion	23	August 5, 2015 02:09
OpenFOAM 1.7.1 installation problem on OpenSUSE 11.3	flakid	OpenFOAM Installation	16	December 28, 2010 08:48
Regarding FoamX running Kindly help out	hariya03	OpenFOAM Pre-Processing	0	April 18, 2008 04:26
[blockMesh] Axisymmetrical mesh	Rasmus Gjesing (Gjesing)	OpenFOAM Meshing & Mesh Conversion	10	April 2, 2007 14:00

July 31, 2012, 05:38		#3
amir00251 New Member Amir Join Date: Sep 2011 Posts: 10 Rep Power: 14	Hello, thanks for your reply. I still cannot select the center line to create a Named Selection after choosing line in selection type. I can create Named selections for the surfaces of the body or for whole body but not for that center line. That center line is just a sketch... this should give a clue? I read in another forum that if you want to create a Named Selection for a closed area inside a surface, you should extrude and change the option from add material to imprint ... something like this is required but I can not extrude a single line??

July 31, 2012, 05:49		#4
flotus1 Super Moderator Alex Join Date: Jun 2012 Location: Germany Posts: 3,399 Rep Power: 46	I see... You need the line only to define the axis of rotation? In your picture, the line coincides with an axis of the global coordinate system. It should be possible to select this axis as the axis of rotation.

July 31, 2012, 06:07		#5
amir00251 New Member Amir Join Date: Sep 2011 Posts: 10 Rep Power: 14	Yes, I was thinkng that I can easily choose z axis as axis of rotation, but again there is not that possibility when I am defining rotatinal velocity ... would you please give details if this is possible.

July 31, 2012, 08:02		#7
amir00251 New Member Amir Join Date: Sep 2011 Posts: 10 Rep Power: 14	Thanks alot for your help, it did solve the problem. I think instead of Named Selection, I should look at how to define a vector... or use component as you pointed out above...