Does any one have circle-pump.msh,input.txt, vane.c, and oil den.c files ?

patilmahesh25 · May 30, 2017, 23:58

Hello all,
I am new in CFD (ANSYS 17.1) analysis of vane pump,wanna to learn through tutorial,but don't have it's input files please help.

Светлана · May 31, 2017, 01:05

Some official ANSYS tutorials have file names so I just search for them on the entire file system because they don't tell where they are... :-/

Which tutorial would you like to follow? Please link to it or give its name and I would try to find its input files or find a similar tutorial whose input files are not missing.

patilmahesh25 · May 31, 2017, 01:22

Hello sir,
Thanks for reply,

This tutorial illustrates how to setup and run a vane pump analysis in ANSYS
FLUENT 13. This tutorial demonstrates how to do the following:
• Create an initial mesh.
• Set up a problem for a dynamic mesh.
• Specify the motion of dynamic zones using a compiled user-defined function (UDF).
• Preview the dynamic mesh before starting the calculation.
• Perform transient dynamic mesh calculation.
• Postprocess the resulting data.

patilmahesh25 · June 3, 2017, 00:17

Name of this tutorial is Vane pump modelling in ANSYS FLUENT

Светлана · June 4, 2017, 22:38

Probably I'm not the right person to ask this question. I don't see any such tutorial in my ANSYS Help section and there is no such file on my hard drive either.

Who is the tutorial from?

May 30, 2017, 23:58	Does any one have circle-pump.msh,input.txt, vane.c, and oil den.c files ?	#1
patilmahesh25 New Member Mahesh Patil Join Date: May 2017 Posts: 3 Rep Power: 8	Hello all, I am new in CFD (ANSYS 17.1) analysis of vane pump,wanna to learn through tutorial,but don't have it's input files please help. Светлана likes this.

May 31, 2017, 01:05	Which tutorial?	#2
Светлана Senior Member Svetlana Tkachenko Join Date: Oct 2013 Location: Australia, Sydney Posts: 407 Rep Power: 14	Some official ANSYS tutorials have file names so I just search for them on the entire file system because they don't tell where they are... :-/ Which tutorial would you like to follow? Please link to it or give its name and I would try to find its input files or find a similar tutorial whose input files are not missing.

May 31, 2017, 01:22	Tutorial: Vane Pump Modeling in ANSYS FLUENT	#3
patilmahesh25 New Member Mahesh Patil Join Date: May 2017 Posts: 3 Rep Power: 8	Hello sir, Thanks for reply, This tutorial illustrates how to setup and run a vane pump analysis in ANSYS FLUENT 13. This tutorial demonstrates how to do the following: • Create an initial mesh. • Set up a problem for a dynamic mesh. • Specify the motion of dynamic zones using a compiled user-defined function (UDF). • Preview the dynamic mesh before starting the calculation. • Perform transient dynamic mesh calculation. • Postprocess the resulting data. Светлана likes this.

June 3, 2017, 00:17	Name of Tutorial: Vane Pump Modeling in ANSYS FLUENT	#4
patilmahesh25 New Member Mahesh Patil Join Date: May 2017 Posts: 3 Rep Power: 8	Name of this tutorial is Vane pump modelling in ANSYS FLUENT Светлана likes this.

June 4, 2017, 22:38	Not official?	#5
Светлана Senior Member Svetlana Tkachenko Join Date: Oct 2013 Location: Australia, Sydney Posts: 407 Rep Power: 14	Probably I'm not the right person to ask this question. I don't see any such tutorial in my ANSYS Help section and there is no such file on my hard drive either. Who is the tutorial from?

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Phase change material in oil pan - solidification	wsh	FLUENT	7	August 14, 2015 06:50