 |
 |
 |
|
|
|
[Sponsors] | ||||
December 30, 2020, 01:49
|
Error in FSI
|
#1 |
|
New Member
Damla Damla
Join Date: Dec 2020
Posts: 3
Rep Power: 5  |
Hi, I am trying to analyze 2-way FSI. In both static structural+steady fluent and transient structural+transient fluent, I have encountered same error:
"Update failed for the Solution component in system coupling. The coupled update for system Static Structural threw an exception. Error updating cell solution in System Static Structural." Solution Information: +-----------------------------------------------------------------------------+ | Warnings were found during data model validation. | +-----------------------------------------------------------------------------+ | Restart output is only requested at last step. To enable restarts from | | intermediate points, use another 'OutputControl' option. | | Participant CouplingParticipant:Solution 1 has the ExecutionControl | | 'Option' set to 'ExternallyManaged'. System Coupling will not control | | the startup/shutdown behavior of this participant. | | Participant CouplingParticipant:Solution has the ExecutionControl 'Option' | | set to 'ExternallyManaged'. System Coupling will not control the | | startup/shutdown behavior of this participant. | +-----------------------------------------------------------------------------+ Awaiting connections from coupling participants... +-----------------------------------------------------------------------------+ | "System coupling solution stopped before all participants connected. A | | solver failure occurred during the run in the Static Structural system" How to solve this problem? Thank you. |
|
|
|
|
|
February 14, 2022, 13:03
|
Warning in Fluent/Thermal Electric system coupling
|
#2 |
|
New Member
Join Date: Feb 2020
Location: Switzerland
Posts: 2
Rep Power: 0 |
Hi wind6, I have the same message, namely:
Code:
+-----------------------------------------------------------------------------+ | Warnings were found during data model validation. | +-----------------------------------------------------------------------------+ | Warning: Participant Fluid Flow (Fluent with Fluent Meshing) | | (CouplingParticipant:Solution 1) has the ExecutionControl 'Option' set | | to 'ExternallyManaged'. System Coupling will not control the | | startup/shutdown behavior of this participant. | | Warning: Participant Thermal-Electric (CouplingParticipant:Solution) has | | the ExecutionControl 'Option' set to 'ExternallyManaged'. System | | Coupling will not control the startup/shutdown behavior of this | | participant. | +-----------------------------------------------------------------------------+ Did you by any chance happen to solve the issue? |
|
|
|
|
|
|
February 19, 2022, 06:38
|
|
#3 |
|
Member
Void_CFD-user
Join Date: Feb 2022
Posts: 67
Rep Power: 4 |
Check if the static simulation runs on its own. Make sure the time step in static and fluids side is the same. Well it system coupling should override the time step anyways. But yea, make sure your simulation runs on its own first.
|
|
|
|
|
|
|
June 5, 2022, 04:37
|
|
#4 | |
|
New Member
Evelyn
Join Date: Mar 2021
Posts: 15
Rep Power: 5 |
Quote:
|
||
|
|
|
||
|
October 20, 2022, 03:14
|
|
#5 | |
|
Member
MANU P ANAND
Join Date: Jul 2014
Location: Daegu , REPUBLIC OF KOREA
Posts: 36
Rep Power: 11 |
Quote:
|
||
|
|
|
||
 |
| Tags |
| fsi |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Help wanted on SU2 Unsteady FSI | lalatuobu | SU2 | 0 | June 30, 2020 03:51 |
| FSI: How to transfer static pressure from fluent to ANSYS | momo_sjx | FLUENT | 0 | October 9, 2012 13:37 |
| BCs in an FSI simulation of a flexble pipe | vivekcfd | OpenFOAM | 10 | January 8, 2010 04:14 |
| fsi | sun | Siemens | 8 | January 19, 2009 23:17 |
| how to extend FSI 2D codes to 3D, need advises | abouziar | Main CFD Forum | 1 | May 30, 2008 04:08 |
Linear Mode
