# stationary flow - transient temperature

 User Name Remember Me Password
 Register Blogs Members List Search Today's Posts Mark Forums Read

 June 2, 2003, 08:00 stationary flow - transient temperature #1 Nicola Guest   Posts: n/a Hey all, I have a complex geometry with two separated fluids with constant velocities and 1.) the same temperature which differs from the solid temperature. I want to calculate the heating up of the solid 2.) one fliud with constant temperature and the other with a varying temperature ramp. I also want to calculate the heating up of the solid As I get a maximum time step of 0.02 s for my flow condition it is quite uncomfortable to calculate fully transient. Is there a possibility to treat the flow as stationary and only the conjugate heat transfer as transient? How can I do the set-up for this calculation? Regards, Nicola

 June 2, 2003, 11:04 Re: stationary flow - transient temperature #2 Joern Beilke Guest   Posts: n/a If you are sure that the flow does not change anymore you can switch off the calculation of velocity, pressure ... and only solve for the temperature with a much larger time step. Later you can switch on the flow for some time steps ...

 June 3, 2003, 08:39 Re: stationary flow - transient temperature #3 Nicola Guest   Posts: n/a Thanks a lot, it's running much faster. Is there an equation for the max time step for conjugate heat transfer equivalent to the equation for the transient piso? Do you know how the convective heat transfer is solved without solving the velocity? Is the existing velocity from the restart file used? Regards, Nicola

 June 10, 2003, 10:11 Re: stationary flow - transient temperature #4 Joern Beilke Guest   Posts: n/a You dont need to stop the calculation every time. Just define some load steps and use different settings for the solve command and the time step size.

 June 16, 2003, 05:04 Re: stationary flow - transient temperature #5 Nicola Guest   Posts: n/a I tried to switch on the flow and pressure calculation for some time steps, with the transient file, in which only the energy equation is solved, as restart file. But it didn't work. Prostar accepts the switch, but in the calculation, it is not solved for neither velocities nor pressure... Havew I to change anything in the previous set-up, or in the .prob file, or somewhere else? Thanks for help, Nicola

 June 16, 2003, 05:44 Re: stationary flow - transient temperature #6 Joern Beilke Guest   Posts: n/a time trans trfi init ! solve all for 10 time steps solve,y,y,y,y,n,n,y,n,n,n,n,n, lstep,1,10,cons,1e-5,N,0,0 lssave,1 ! solve temperature for 100 steps solve,n,n,n,n,n,n,y,n,n,n,n,n, lstep,2,100,cons,1,N,0,0 lssave,2 ! solve all for 10 time steps solve,y,y,y,y,n,n,y,n,n,n,n,n, lstep,2,10,cons,1e-5,N,0,0 lssave,2 lsra 1 3 ...

 Thread Tools Display Modes Linear Mode

 Posting Rules You may not post new threads You may not post replies You may not post attachments You may not edit your posts BB code is On Smilies are On [IMG] code is On HTML code is OffTrackbacks are On Pingbacks are On Refbacks are On Forum Rules

 Similar Threads Thread Thread Starter Forum Replies Last Post basilwatson OpenFOAM Running, Solving & CFD 1 May 26, 2008 06:37 manuel OpenFOAM Running, Solving & CFD 6 March 24, 2007 19:23 Peter CFX 1 June 27, 2006 17:50 R.Sripriya Main CFD Forum 0 May 13, 2005 06:07 Ravi Main CFD Forum 0 May 7, 2003 09:43

All times are GMT -4. The time now is 22:47.

 Contact Us - CFD Online - Top