Ansys Workbench mesh generation

Hamilton · December 24, 2012, 01:15

Hi to every one,
In fact I am trying to simulate a FSI problem in Ansys Workbench. For mesh generation of solid and fluid the Workbench uses ICEM software but I want to use CFX mesh generation software, how can I solve this problem ?

sincerely

zandi · December 24, 2012, 01:28

Hi
do you mean you want to work with workbench?
it has two parts design modeler and cfx mesh. you can do it easily by workbench.

Hamilton · December 24, 2012, 22:43

Hi Mrs. Zandi and thanks for your reply,
In fact I want to use use work bench with CFX mesh generation but unfortunately ICEM mesh generation always loads NOT CFX mesh generation.

sincerely

zandi · December 25, 2012, 02:04

hi workbench and icem-cfd are two independent parts which are located in ANSYS sofware pack. I did not use icem-cfd and just have a friend worked on it. I have used workbench for meshing. it has cfx-mesh.

Hamilton · December 25, 2012, 22:49

Thank you for your reply.

Sixkillers · December 26, 2012, 04:14

ANSYS CFX isn't able to remesh a geometry by its own (Fluent does). As was mentioned you can use either ICEM CFD, or ANSYS Meshing. If you want to use ANSYS Meshing for remeshing process definitely take a look at the following tutorial (http://www.edr.no/blogg/ansys_blogge...nch_cfx_remesh).

December 24, 2012, 01:15	Ansys Workbench mesh generation	#1
Hamilton Member Alireza Safikhani Join Date: Dec 2010 Posts: 36 Rep Power: 15	Hi to every one, In fact I am trying to simulate a FSI problem in Ansys Workbench. For mesh generation of solid and fluid the Workbench uses ICEM software but I want to use CFX mesh generation software, how can I solve this problem ? sincerely

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
ANSYS Workbench mesh crashes (ANSYSWBU.exe problem)	kondan	ANSYS	76	February 22, 2024 02:27
Gambit problems	Althea	FLUENT	22	January 4, 2017 03:19
importing mesh from Gambit and other software to ansys workbench	mortazavi	CFX	12	May 30, 2012 07:38
Mesh Seeds in ANSYS WorkBench Meshing	smcp	ANSYS	1	March 12, 2012 13:16
[Gmsh] 2D Mesh Generation Tutorial for GMSH	aeroslacker	OpenFOAM Meshing & Mesh Conversion	12	January 19, 2012 03:52

December 24, 2012, 01:28		#2
zandi Senior Member Fatema Zandi Goharrizi Join Date: Mar 2009 Posts: 158 Rep Power: 17	Hi do you mean you want to work with workbench? it has two parts design modeler and cfx mesh. you can do it easily by workbench.

December 24, 2012, 22:43		#3
Hamilton Member Alireza Safikhani Join Date: Dec 2010 Posts: 36 Rep Power: 15	Hi Mrs. Zandi and thanks for your reply, In fact I want to use use work bench with CFX mesh generation but unfortunately ICEM mesh generation always loads NOT CFX mesh generation. sincerely

December 25, 2012, 02:04		#4
zandi Senior Member Fatema Zandi Goharrizi Join Date: Mar 2009 Posts: 158 Rep Power: 17	hi workbench and icem-cfd are two independent parts which are located in ANSYS sofware pack. I did not use icem-cfd and just have a friend worked on it. I have used workbench for meshing. it has cfx-mesh.

December 25, 2012, 22:49		#5
Hamilton Member Alireza Safikhani Join Date: Dec 2010 Posts: 36 Rep Power: 15	Thank you for your reply.

December 26, 2012, 04:14		#6
Sixkillers Member Join Date: Nov 2011 Location: Czech Republic Posts: 97 Rep Power: 14	ANSYS CFX isn't able to remesh a geometry by its own (Fluent does). As was mentioned you can use either ICEM CFD, or ANSYS Meshing. If you want to use ANSYS Meshing for remeshing process definitely take a look at the following tutorial (http://www.edr.no/blogg/ansys_blogge...nch_cfx_remesh).