transient final time step results

hmasenger · September 17, 2013, 00:15

hi all
i am running an adaptive transient model and i just need the final time step's results
does any one know how can i set output frequency to just save the results achieved in the final time step ?

regards

Dave442 · September 17, 2013, 06:20

Hi hmasenger,

For a regular transient analyses you can get CFX to output specific variables at specific time steps by double clicking on "Output Control" in the outline tree in CFX-Pre and adjusting the controls in the "Transient Results" tab. This is described pretty well in the "Output Controls" section of the CFX-Pre Users Guide.

But maybe your asking because this is not possible for an adaptive run?

Hope this helps,
Dave

ghorrocks · September 17, 2013, 06:21

If you just want to save the final time step then do not put any transient results files in the output tab of CFX-Pre, and make sure the results file settings are good. This is how results files are set up by default, so if it is anything else then you have changed it from the defaults.

Dave442 · September 17, 2013, 06:32

hmasenger,

Glenn is correct. I forgot that CFX outputs the results from the final time step by default!

My bad,
Dave

hmasenger · September 17, 2013, 10:31

tanks again glenn you got what i meant.
it worked fine

singer1812 · September 17, 2013, 11:24

A helpful feature in running like this, is to use Backup Results (Not Transient Results) every XX timesteps/time_interval also. This way when running a transient, and if it stops/crashes for whatever reason prior to the end, you have a startup point without restarting from 0.

The Backup Results will overwrite each other, saving only the last backup.

September 17, 2013, 00:15	transient final time step results	#1
hmasenger Senior Member hamed Join Date: Apr 2009 Posts: 148 Rep Power: 17	hi all i am running an adaptive transient model and i just need the final time step's results does any one know how can i set output frequency to just save the results achieved in the final time step ? regards

September 17, 2013, 06:21		#3
ghorrocks Super Moderator Glenn Horrocks Join Date: Mar 2009 Location: Sydney, Australia Posts: 17,703 Rep Power: 143	If you just want to save the final time step then do not put any transient results files in the output tab of CFX-Pre, and make sure the results file settings are good. This is how results files are set up by default, so if it is anything else then you have changed it from the defaults. hmasenger likes this.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Transient simulation not converging	skabilan	OpenFOAM Running, Solving & CFD	14	December 16, 2019 23:12
How to write k and epsilon before the abnormal end	xiuying	OpenFOAM Running, Solving & CFD	8	August 27, 2013 15:33
dynamic Mesh is faster than MRF????	sharonyue	OpenFOAM Running, Solving & CFD	14	August 26, 2013 07:47
Full pipe 3D using icoFoam	cyberbrain	OpenFOAM	4	March 16, 2011 09:20
IcoFoam parallel woes	msrinath80	OpenFOAM Running, Solving & CFD	9	July 22, 2007 02:58

September 17, 2013, 06:20		#2
Dave442 Member Dave Join Date: Aug 2011 Posts: 33 Rep Power: 14	Hi hmasenger, For a regular transient analyses you can get CFX to output specific variables at specific time steps by double clicking on "Output Control" in the outline tree in CFX-Pre and adjusting the controls in the "Transient Results" tab. This is described pretty well in the "Output Controls" section of the CFX-Pre Users Guide. But maybe your asking because this is not possible for an adaptive run? Hope this helps, Dave

September 17, 2013, 06:32		#4
Dave442 Member Dave Join Date: Aug 2011 Posts: 33 Rep Power: 14	hmasenger, Glenn is correct. I forgot that CFX outputs the results from the final time step by default! My bad, Dave

September 17, 2013, 10:31		#5
hmasenger Senior Member hamed Join Date: Apr 2009 Posts: 148 Rep Power: 17	tanks again glenn you got what i meant. it worked fine

September 17, 2013, 11:24		#6
singer1812 Senior Member Edmund Singer P.E. Join Date: Aug 2010 Location: Minneapolis, MN Posts: 511 Rep Power: 20	A helpful feature in running like this, is to use Backup Results (Not Transient Results) every XX timesteps/time_interval also. This way when running a transient, and if it stops/crashes for whatever reason prior to the end, you have a startup point without restarting from 0. The Backup Results will overwrite each other, saving only the last backup.