Modeling a complex geometry

rzamorano · October 1, 2013, 17:28

Hi, i have to model a spillway with vaiable width, curvatures and changes of slope and i can't make the geometry of this. Before that Design Modeler was enough for me but now i need a solution in how can do this.
Wich software recomend to do the geometry and how can export that to ANSYS without trouble. Please help i need a solution for this

ghorrocks · October 1, 2013, 20:38

Any major solid modelling package (Solidworks, Pro-Engineer, Inventor, Unigraphics etc) interfaces with ANSYS just fine.

rzamorano · October 2, 2013, 10:56

thanks, i would like to do something like this http://www.youtube.com/watch?v=MZqSvHcU-cA in ansys cfx. any suggestion?

ghorrocks · October 2, 2013, 18:01

Did you read my post? If you cannot define your geometry in Designmodeller then any serious solid modelling package will do it.

rzamorano · October 2, 2013, 18:04

yes i read it, but i wrote wrong my question, wich one of those software do you recomend? because i know just a litle bit of CAD, thank you again for response my questions

October 1, 2013, 17:28	Modeling a complex geometry	#1
rzamorano New Member Rodrigo Join Date: Oct 2013 Posts: 4 Rep Power: 12	Hi, i have to model a spillway with vaiable width, curvatures and changes of slope and i can't make the geometry of this. Before that Design Modeler was enough for me but now i need a solution in how can do this. Wich software recomend to do the geometry and how can export that to ANSYS without trouble. Please help i need a solution for this

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Modeling Propeller Geometry in STAR CCM+ 3D-CAD	tava.amitava	STAR-CCM+	16	October 25, 2021 07:45
[GAMBIT] About creating complex geometry	cdoferreira	ANSYS Meshing & Geometry	16	September 17, 2012 02:29
heat transfer in an orthotropic material and complex curved geometry	zayzan	FLUENT	0	October 11, 2011 10:47
[ICEM] Complex 3D geometry Hexa blocking and inflation layer	Chipsgrottel	ANSYS Meshing & Geometry	4	September 30, 2011 03:25
How to construct complex 3D geometry using GAMBIT?	Feng	FLUENT	5	October 11, 2005 04:13

October 1, 2013, 20:38		#2
ghorrocks Super Moderator Glenn Horrocks Join Date: Mar 2009 Location: Sydney, Australia Posts: 17,692 Rep Power: 143	Any major solid modelling package (Solidworks, Pro-Engineer, Inventor, Unigraphics etc) interfaces with ANSYS just fine.

October 2, 2013, 10:56		#3
rzamorano New Member Rodrigo Join Date: Oct 2013 Posts: 4 Rep Power: 12	thanks, i would like to do something like this http://www.youtube.com/watch?v=MZqSvHcU-cA in ansys cfx. any suggestion?

October 2, 2013, 18:01		#4
ghorrocks Super Moderator Glenn Horrocks Join Date: Mar 2009 Location: Sydney, Australia Posts: 17,692 Rep Power: 143	Did you read my post? If you cannot define your geometry in Designmodeller then any serious solid modelling package will do it.

October 2, 2013, 18:04		#5
rzamorano New Member Rodrigo Join Date: Oct 2013 Posts: 4 Rep Power: 12	yes i read it, but i wrote wrong my question, wich one of those software do you recomend? because i know just a litle bit of CAD, thank you again for response my questions