Problems in the deployment temperature

Zero · December 17, 2013, 00:59

Dear all,

First im sorry if my poor language skills, i have a problem to simulation ansys cfx 2013. I have made an experiment on a cube and I insert an object into the cube. Cube was rather like the room and the object is a machine that has a temperature of 100 Celsius. In my pre CFX-cube into the air stream with a temperature of 25 Celsius and some other settings.

And at this stage of the CFX-post I made sebuat plane and I named plane 1. Variable on the first plane I set it as a base for cross-sectional temperature but the results do not spread on the plane, while if 1 variable on my plane to pressure or viscosity change there will be a deployment on the plane.

If you all have a solution please explanation, thank you..

ghorrocks · December 17, 2013, 04:20

Can you post some images of what you are seeing, and include your CCL.

Zero · December 18, 2013, 19:41

yes but may i know your address mail glenn because too large capacity if i send here ?

Zero · December 19, 2013, 10:02

Result of Temperature (failed deployment at plane)

Zero · December 19, 2013, 10:14

Result of Pressure (Success deployment at plane)

Setting model at cfx-pre

Zero · December 19, 2013, 10:21

Setting Domain

Setting Material

ghorrocks · December 19, 2013, 16:26

Is the interface connecting the solid and fluid domains correct?

Is your simulation converged?

Do you need to run it for longer physical time? Convergence of CHT simulations cannot be judged by residuals alone. You often need to add imbalances as a convergence critereon.

Zero · December 22, 2013, 20:14

Setting Interface

Have you ever done the experiment of heat transfer (CHT)?

Can you show me (tutorial) step by step about to add imbalances as a convergence critereon ?

ghorrocks · December 23, 2013, 06:35

Do the CHT tutorials provided with CFX. The heating coil is a good one.

Imbalances are an option under convergence control.

December 17, 2013, 00:59	Problems in the deployment temperature	#1
Zero New Member Arief Join Date: Sep 2013 Location: Surabaya Posts: 12 Rep Power: 12	Dear all, First im sorry if my poor language skills, i have a problem to simulation ansys cfx 2013. I have made an experiment on a cube and I insert an object into the cube. Cube was rather like the room and the object is a machine that has a temperature of 100 Celsius. In my pre CFX-cube into the air stream with a temperature of 25 Celsius and some other settings. And at this stage of the CFX-post I made sebuat plane and I named plane 1. Variable on the first plane I set it as a base for cross-sectional temperature but the results do not spread on the plane, while if 1 variable on my plane to pressure or viscosity change there will be a deployment on the plane. If you all have a solution please explanation, thank you..

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Problem with zeroGradient wall BC for temperature - Total temperature loss	cboss	OpenFOAM	12	October 1, 2018 06:36
Free stream temperature in tube wall	saharesobh	FLUENT	2	November 19, 2012 07:32
Temperature went outside of its upper limit	Atit Koonsrisuk	CFX	0	January 8, 2004 11:43
Problems in CFX 5.5.1	Sulviyanti	CFX	6	February 7, 2003 16:46
chemical reaction - decompostition	La S. Hyuck	CFX	1	May 23, 2001 00:07

December 17, 2013, 04:20		#2
ghorrocks Super Moderator Glenn Horrocks Join Date: Mar 2009 Location: Sydney, Australia Posts: 17,703 Rep Power: 143	Can you post some images of what you are seeing, and include your CCL.

December 18, 2013, 19:41		#3
Zero New Member Arief Join Date: Sep 2013 Location: Surabaya Posts: 12 Rep Power: 12	yes but may i know your address mail glenn because too large capacity if i send here ?

December 19, 2013, 16:26		#7
ghorrocks Super Moderator Glenn Horrocks Join Date: Mar 2009 Location: Sydney, Australia Posts: 17,703 Rep Power: 143	Is the interface connecting the solid and fluid domains correct? Is your simulation converged? Do you need to run it for longer physical time? Convergence of CHT simulations cannot be judged by residuals alone. You often need to add imbalances as a convergence critereon.

December 23, 2013, 06:35		#9
ghorrocks Super Moderator Glenn Horrocks Join Date: Mar 2009 Location: Sydney, Australia Posts: 17,703 Rep Power: 143	Do the CHT tutorials provided with CFX. The heating coil is a good one. Imbalances are an option under convergence control.