free falling of a wedge into water

ghoroobeaakhar · April 20, 2014, 11:40

I'm trying to model free falling of a wedge into water.

http://www.mediafire.com/watch/1d8k9...wr/CFXfull.mp4

the problem is that the velocity of wedge after impact doesn't reduce and it maintains its speed as you see.

thanks.

ghorrocks · April 20, 2014, 23:31

This could be real - if the wedge is heavy and you are looking at the first entry into the water it may be correct that the wedge has not slowed down much.

Or this could be due to simulation error or inaccuracy.

So before trying anything, are you sure what you are seeing is correct or not?

ghoroobeaakhar · April 21, 2014, 10:58

my results for velocity and acceleration of wedge
13 for velocity
14 for acceleration

ghoroobeaakhar · April 21, 2014, 11:04

but in fact something like the picture should happen.
(a sudden decreasing in speed)
thanks.

ghorrocks · April 22, 2014, 06:14

So it looks like your simulation is inaccurate. This is an FAQ: http://www.cfd-online.com/Wiki/Ansys..._inaccurate.3F

Manigandan.R · April 22, 2014, 06:30

Please increase the water height bit more may be it will help out to do the modelling , meshing & analysis once again. Or otherwise reduce the dropping velocity make it small. May be it will help you out.

ghoroobeaakhar · April 23, 2014, 12:28

ghorrocks and Manigandan.R
thanks.
I increased the water height and reduced the velocity and time steps.
I increased the number nodes and elements (meshing). it's running now and I hope it works.

April 20, 2014, 11:40	free falling of a wedge into water	#1
ghoroobeaakhar Member aliali Join Date: Apr 2014 Posts: 35 Rep Power: 12	I'm trying to model free falling of a wedge into water. http://www.mediafire.com/watch/1d8k9...wr/CFXfull.mp4 the problem is that the velocity of wedge after impact doesn't reduce and it maintains its speed as you see. thanks.

April 20, 2014, 23:31		#2
ghorrocks Super Moderator Glenn Horrocks Join Date: Mar 2009 Location: Sydney, Australia Posts: 17,697 Rep Power: 143	This could be real - if the wedge is heavy and you are looking at the first entry into the water it may be correct that the wedge has not slowed down much. Or this could be due to simulation error or inaccuracy. So before trying anything, are you sure what you are seeing is correct or not? ghoroobeaakhar likes this.

April 22, 2014, 06:14		#5
ghorrocks Super Moderator Glenn Horrocks Join Date: Mar 2009 Location: Sydney, Australia Posts: 17,697 Rep Power: 143	So it looks like your simulation is inaccurate. This is an FAQ: http://www.cfd-online.com/Wiki/Ansys..._inaccurate.3F ghoroobeaakhar likes this.

April 22, 2014, 06:30		#6
Manigandan.R New Member Manigandan.R Join Date: Mar 2011 Posts: 10 Rep Power: 15	Please increase the water height bit more may be it will help out to do the modelling , meshing & analysis once again. Or otherwise reduce the dropping velocity make it small. May be it will help you out. ghoroobeaakhar likes this.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

April 23, 2014, 12:28		#7
ghoroobeaakhar Member aliali Join Date: Apr 2014 Posts: 35 Rep Power: 12	ghorrocks and Manigandan.R thanks. I increased the water height and reduced the velocity and time steps. I increased the number nodes and elements (meshing). it's running now and I hope it works.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Mass imbalance problem in multiphase water and steam CFX case	Antech	CFX	1	October 26, 2020 04:03
simulation of free falling sphere into calm water?	pedyspider	CFX	17	June 25, 2015 11:03
Wedge water impact DFBI Overset mesh	jcamilleri	STAR-CCM+	1	March 31, 2014 12:58
question about simulation of falling water film	mengyue1	FLUENT	2	March 30, 2014 10:16
Modeling of free surface water waves	John N.	CFX	3	January 21, 2009 00:07