transient time

mina.p · April 25, 2014, 13:52

Hi
I simulate the heat transfer in a channel with steady state setting & 1000 iteration
after that i do the same simulation in transient mode with total time:400 & timestep:0.01
but i still didn't reach the steady state data
can any body help me in time setting for transient??

ghorrocks · April 26, 2014, 06:27

This FAQ discusses these sort of issues a little bit: http://www.cfd-online.com/Wiki/Ansys...gence_criteria

Are you sure your simulation is steady state anyway? It will never converge with a steady model if the flow is actually transient.

mina.p · April 26, 2014, 07:20

I simulate a channel with a blade in it.at first the blade is steady afTer that i do the simulation for rotating blade
So i do the first part with steady state setting and it converges.
But i do it again with transient to know the approximate total time for the case of moving blade.
But it take long time and still didn't converge.

ghorrocks · April 26, 2014, 07:24

Can you post an image of what you are modelling?

mina.p · April 26, 2014, 07:36

http://www.imageupload.co.uk/gAZ
http://www.imageupload.co.uk/gA5
total temperature of steady state and transient with total time=500 & time step=.01

ghorrocks · April 26, 2014, 07:47

Have you read the FAQ I linked to in the first post? All the issues you should be looking at are described there.

April 25, 2014, 13:52	transient time	#1
mina.p New Member mina Join Date: Nov 2013 Posts: 20 Rep Power: 12	Hi I simulate the heat transfer in a channel with steady state setting & 1000 iteration after that i do the same simulation in transient mode with total time:400 & timestep:0.01 but i still didn't reach the steady state data can any body help me in time setting for transient??

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
AMI speed performance	danny123	OpenFOAM	21	October 24, 2020 04:13
Moving mesh	Niklas Wikstrom (Wikstrom)	OpenFOAM Running, Solving & CFD	122	June 15, 2014 06:20
AMI interDyMFoam for mixer nu problem	danny123	OpenFOAM Programming & Development	8	September 6, 2013 02:34
Transient simulation : Static temperature and time averaged static temperature	saisanthoshm88	CFX	4	July 4, 2013 02:18
calculation diverge after continue to run	zhajingjing	OpenFOAM	0	April 28, 2010 04:35

April 26, 2014, 06:27		#2
ghorrocks Super Moderator Glenn Horrocks Join Date: Mar 2009 Location: Sydney, Australia Posts: 17,703 Rep Power: 143	This FAQ discusses these sort of issues a little bit: http://www.cfd-online.com/Wiki/Ansys...gence_criteria Are you sure your simulation is steady state anyway? It will never converge with a steady model if the flow is actually transient.

April 26, 2014, 07:20		#3
mina.p New Member mina Join Date: Nov 2013 Posts: 20 Rep Power: 12	I simulate a channel with a blade in it.at first the blade is steady afTer that i do the simulation for rotating blade So i do the first part with steady state setting and it converges. But i do it again with transient to know the approximate total time for the case of moving blade. But it take long time and still didn't converge.

April 26, 2014, 07:24		#4
ghorrocks Super Moderator Glenn Horrocks Join Date: Mar 2009 Location: Sydney, Australia Posts: 17,703 Rep Power: 143	Can you post an image of what you are modelling?

April 26, 2014, 07:36		#5
mina.p New Member mina Join Date: Nov 2013 Posts: 20 Rep Power: 12	http://www.imageupload.co.uk/gAZ http://www.imageupload.co.uk/gA5 total temperature of steady state and transient with total time=500 & time step=.01

April 26, 2014, 07:47		#6
ghorrocks Super Moderator Glenn Horrocks Join Date: Mar 2009 Location: Sydney, Australia Posts: 17,703 Rep Power: 143	Have you read the FAQ I linked to in the first post? All the issues you should be looking at are described there.