 |
 |
 |
|
|
|
[Sponsors] | ||||
August 23, 2012, 15:50
|
Modeling the fan with a mass flow interface
|
#1 |
|
Senior Member
---------
Join Date: Oct 2010
Posts: 303
Rep Power: 17  |
To model a fan just with it's operating point in CFX , I chose the front face of the fan as an interface and specified the mass flow at the operating point by selecting the mass flow interface model in the additional interface models tab.
The fan is actually located in a domain with pressure inlets and pressure outlets and now the fan front face provides the suction of air it is therefore modeled as the mass flow interface with that mass flow as it would have at it's operating point. Could some one please let me know if this is a valid approach.
__________________
Best regards, Santhosh. |
|
|
|
|
|
August 23, 2012, 18:48
|
|
#2 |
|
Super Moderator
Glenn Horrocks
Join Date: Mar 2009
Location: Sydney, Australia
Posts: 17,692
Rep Power: 143 |
This is a valid approach providing the pressure drop across the fan is the right one for the flow rate it is delivering.
|
|
|
|
|
|
|
August 23, 2012, 22:51
|
|
#3 |
|
Senior Member
Erik
Join Date: Feb 2011
Location: Earth (Land portion)
Posts: 1,167
Rep Power: 23 |
What are you doing with the back of the fan?
|
|
|
|
|
|
|
August 24, 2012, 04:26
|
|
#4 |
|
Senior Member
---------
Join Date: Oct 2010
Posts: 303
Rep Power: 17 |
I didn't specify the pressure drop at the interface but I just specified the mass flow at the interface and this is from the operating point data of the fan.
Please look into the attached image , it may not exactly depict my domain but it throws a better illustration. As shown in the image I only know that the inlet and outlet are just pressure boundaries at atmospheric pressure no other information is available. I'm very much particular in having both the inlet and outlet as pressure based boundaries.
__________________
Best regards, Santhosh. |
|
|
|
|
|
|
August 24, 2012, 07:39
|
|
#5 |
|
Super Moderator
Glenn Horrocks
Join Date: Mar 2009
Location: Sydney, Australia
Posts: 17,692
Rep Power: 143 |
Yes, this is a valid approach providing the fan stays at its operating point.
|
|
|
|
|
|
|
August 1, 2014, 04:18
|
Finding fan curve
|
#6 |
|
Member
hashim chaudhry
Join Date: Jun 2014
Location: turkey
Posts: 46
Rep Power: 11  |
Hi I am quite new to CFD i am trying to find out the fan curve what did uptill now I made inlet duct 15 times of fan dia with pressure inlet (0.0 Pa), outlet duct 30 times of fan dia with pressure outlet (0.0 Pa) and I am giving fixed rpm to the rotating region in between. I am measuring pressure in inlet and outlet duct at a position 10 times of fan dia. but Still I didnt find the relevant pressure difference across the fan and also the solution is not converges
I would be very grateful if you people help me out |
|
|
|
|
|
|
August 1, 2014, 06:11
|
|
#7 |
|
Super Moderator
Glenn Horrocks
Join Date: Mar 2009
Location: Sydney, Australia
Posts: 17,692
Rep Power: 143 |
Sounds like an FAQ: http://www.cfd-online.com/Wiki/Ansys...gence_criteria
or this one: http://www.cfd-online.com/Wiki/Ansys..._inaccurate.3F |
|
|
|
|
|
 |
| Thread Tools | Search this Thread |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Simulation of Axial Fan Flow using A Momentum Source Subdomain | Liam | CFX | 28 | July 16, 2013 08:24 |
| how to set BC for compressible flow target mass flow rate | foolboy007 | FLUENT | 1 | April 4, 2012 03:24 |
| Species mass flow inlet | lorenz | FLUENT | 3 | March 15, 2012 07:26 |
| Boundary condition for exhaut flow with imposed mass flow | stephane | FLUENT | 1 | November 24, 2011 02:04 |
| reversed flow at velocity inlet / mass flow inlet | ib | FLUENT | 1 | March 26, 2007 13:11 |
1Likes
Linear Mode
