Setting rotating frame of referece.

RPFigueiredo · October 27, 2014, 09:19

Hello!

I'd like to ask a few insights on my setup for a rotating impeller,as seen on the image:

http://s13.postimg.org/hzakt4dmf/image.jpg

Let's go over each domain and boundaries/interfaces:

DOMAIN ANEL

Continuous fluid, 1MPa reference pressure, Stationary, Shear Stress Transport

Anel_walls: non slip smooth wall
Outlet: Average static pressure 7.6MPa/PPres. Profile Blend 0.05
Domain interface 2 side 2: interface, conservative interface flux

DOMAIN DUTO

Continuous fluid, 1MPa reference pressure, Stationary, Shear Stress Transport

Duto_walls: non slip smooth wall
Inlet: Mass Flow rate 14kg/s/Normal to boundary/Zero gradient turbulence
Domain interface 1 side 1: Conservatice Interface Flux

DOMAIN IMPELIDOR

Continuous fluid, Reference 1MPa, Rotating -24000rpm about global Y

Domain interface 1 side 2: conservative interface flux
Domain interface 2 side 2: conservative interface flux
Imp_walls: Frame type rotating, no slip smooth wall

INTERFACES

Domain interface 1: General connection, Frozen rotor, Pitch ratio 1
Domain interface 2: General connection, Frozen rotor, Pitch ratio 1

About solver control, timestep is set to physical, 4.167e-6s. So, is there something too wrong? bacause the solver refuses to run over iteration 1! Any input would be appreciated.

Thank you in advance!

ghorrocks · October 27, 2014, 16:25

Please post your output file.

Also note that it appears you could model this with a single rotating domain, and no stationary domains. Then there is no need for interfaces.

RPFigueiredo · October 28, 2014, 04:58

I realize I could avoid the interfaces. I tried it with the single RFR, but it wouldn't work, so I added the stationary as I will eventually have to model the volute (once I figure out the issue).

Here's the out file:

This run of the CFX-14.0 Solver started at 07:56:04 on 28 Oct 2014 by
user Rolando on ROLANDO-PC (intel_xeon64.sse2_winnt) using the command:

"C:\Program Files\ANSYS Inc\v140\CFX\bin\perllib\cfx5solve.pl"
-stdout-comms -batch -ccl -

Setting up CFX Solver run ...

+--------------------------------------------------------------------+
| |
| CFX Command Language for Run |
| |
+--------------------------------------------------------------------+

LIBRARY:
MATERIAL: Water
Material Description = Water (liquid)
Material Group = Water Data, Constant Property Liquids
Option = Pure Substance
Thermodynamic State = Liquid
PROPERTIES:
Option = General Material
EQUATION OF STATE:
Density = 997.0 [kg m^-3]
Molar Mass = 18.02 [kg kmol^-1]
Option = Value
END
SPECIFIC HEAT CAPACITY:
Option = Value
Specific Heat Capacity = 4181.7 [J kg^-1 K^-1]
Specific Heat Type = Constant Pressure
END
REFERENCE STATE:
Option = Specified Point
Reference Pressure = 1 [atm]
Reference Specific Enthalpy = 0.0 [J/kg]
Reference Specific Entropy = 0.0 [J/kg/K]
Reference Temperature = 25 [C]
END
DYNAMIC VISCOSITY:
Dynamic Viscosity = 8.899E-4 [kg m^-1 s^-1]
Option = Value
END
THERMAL CONDUCTIVITY:
Option = Value
Thermal Conductivity = 0.6069 [W m^-1 K^-1]
END
ABSORPTION COEFFICIENT:
Absorption Coefficient = 1.0 [m^-1]
Option = Value
END
SCATTERING COEFFICIENT:
Option = Value
Scattering Coefficient = 0.0 [m^-1]
END
REFRACTIVE INDEX:
Option = Value
Refractive Index = 1.0 [m m^-1]
END
THERMAL EXPANSIVITY:
Option = Value
Thermal Expansivity = 2.57E-04 [K^-1]
END
END
END
END
FLOW: Flow Analysis 1
SOLUTION UNITS:
Angle Units = [rad]
Length Units = [m]
Mass Units = [kg]
Solid Angle Units = [sr]
Temperature Units = [K]
Time Units = [s]
END
ANALYSIS TYPE:
Option = Steady State
EXTERNAL SOLVER COUPLING:
Option = None
END
END
DOMAIN: Anel
Coord Frame = Coord 0
Domain Type = Fluid
Location = LIVE
BOUNDARY: Anel_walls
Boundary Type = WALL
Location = WALLS 2
BOUNDARY CONDITIONS:
MASS AND MOMENTUM:
Option = No Slip Wall
END
WALL ROUGHNESS:
Option = Smooth Wall
END
END
END
BOUNDARY: Domain Interface 2 Side 2
Boundary Type = INTERFACE
Location = INLET 2
BOUNDARY CONDITIONS:
MASS AND MOMENTUM:
Option = Conservative Interface Flux
END
TURBULENCE:
Option = Conservative Interface Flux
END
END
END
BOUNDARY: Outlet
Boundary Type = OUTLET
Location = OUTLET 2
BOUNDARY CONDITIONS:
FLOW REGIME:
Option = Subsonic
END
MASS AND MOMENTUM:
Option = Average Static Pressure
Pressure Profile Blend = 0.05
Relative Pressure = 7.6 [MPa]
END
PRESSURE AVERAGING:
Option = Average Over Whole Outlet
END
END
END
DOMAIN MODELS:
BUOYANCY MODEL:
Option = Non Buoyant
END
DOMAIN MOTION:
Option = Stationary
END
MESH DEFORMATION:
Option = None
END
REFERENCE PRESSURE:
Reference Pressure = 1 [MPa]
END
END
FLUID DEFINITION: Fluid 1
Material = Water
Option = Material Library
MORPHOLOGY:
Option = Continuous Fluid
END
END
FLUID MODELS:
COMBUSTION MODEL:
Option = None
END
HEAT TRANSFER MODEL:
Fluid Temperature = 25 [C]
Option = Isothermal
END
THERMAL RADIATION MODEL:
Option = None
END
TURBULENCE MODEL:
Option = k epsilon
END
TURBULENT WALL FUNCTIONS:
Option = Scalable
END
END
END
DOMAIN: Duto
Coord Frame = Coord 0
Domain Type = Fluid
Location = SOLID
BOUNDARY: Domain Interface 1 Side 1
Boundary Type = INTERFACE
Location = OUTLET
BOUNDARY CONDITIONS:
MASS AND MOMENTUM:
Option = Conservative Interface Flux
END
TURBULENCE:
Option = Conservative Interface Flux
END
END
END
BOUNDARY: Duto_walls
Boundary Type = WALL
Location = WALLS
BOUNDARY CONDITIONS:
MASS AND MOMENTUM:
Option = No Slip Wall
END
WALL ROUGHNESS:
Option = Smooth Wall
END
END
END
BOUNDARY: Inlet
Boundary Type = INLET
Location = INLET
BOUNDARY CONDITIONS:
FLOW DIRECTION:
Option = Normal to Boundary Condition
END
FLOW REGIME:
Option = Subsonic
END
MASS AND MOMENTUM:
Mass Flow Rate = 14.027 [kg s^-1]
Option = Mass Flow Rate
END
TURBULENCE:
Option = Zero Gradient
END
END
END
DOMAIN MODELS:
BUOYANCY MODEL:
Option = Non Buoyant
END
DOMAIN MOTION:
Option = Stationary
END
MESH DEFORMATION:
Option = None
END
REFERENCE PRESSURE:
Reference Pressure = 1 [MPa]
END
END
FLUID DEFINITION: Fluid 1
Material = Water
Option = Material Library
MORPHOLOGY:
Option = Continuous Fluid
END
END
FLUID MODELS:
COMBUSTION MODEL:
Option = None
END
HEAT TRANSFER MODEL:
Fluid Temperature = 25 [C]
Option = Isothermal
END
THERMAL RADIATION MODEL:
Option = None
END
TURBULENCE MODEL:
Option = k epsilon
END
TURBULENT WALL FUNCTIONS:
Option = Scalable
END
END
END
DOMAIN: Impelidor
Coord Frame = Coord 0
Domain Type = Fluid
Location = CREATED_MATERIAL_10
BOUNDARY: Domain Interface 1 Side 2
Boundary Type = INTERFACE
Location = INLET 3
BOUNDARY CONDITIONS:
MASS AND MOMENTUM:
Option = Conservative Interface Flux
END
TURBULENCE:
Option = Conservative Interface Flux
END
END
END
BOUNDARY: Domain Interface 2 Side 1
Boundary Type = INTERFACE
Location = OUTLET 3
BOUNDARY CONDITIONS:
MASS AND MOMENTUM:
Option = Conservative Interface Flux
END
TURBULENCE:
Option = Conservative Interface Flux
END
END
END
BOUNDARY: Imp_walls
Boundary Type = WALL
Frame Type = Rotating
Location = WALLS 3
BOUNDARY CONDITIONS:
MASS AND MOMENTUM:
Option = No Slip Wall
END
WALL ROUGHNESS:
Option = Smooth Wall
END
END
END
DOMAIN MODELS:
BUOYANCY MODEL:
Option = Non Buoyant
END
DOMAIN MOTION:
Angular Velocity = -24000 [rev min^-1]
Option = Rotating
AXIS DEFINITION:
Option = Coordinate Axis
Rotation Axis = Coord 0.2
END
END
MESH DEFORMATION:
Option = None
END
REFERENCE PRESSURE:
Reference Pressure = 1 [MPa]
END
END
FLUID DEFINITION: Fluid 1
Material = Water
Option = Material Library
MORPHOLOGY:
Option = Continuous Fluid
END
END
FLUID MODELS:
COMBUSTION MODEL:
Option = None
END
HEAT TRANSFER MODEL:
Fluid Temperature = 25 [C]
Option = Isothermal
END
THERMAL RADIATION MODEL:
Option = None
END
TURBULENCE MODEL:
Option = k epsilon
END
TURBULENT WALL FUNCTIONS:
Option = Scalable
END
END
END
DOMAIN INTERFACE: Domain Interface 1
Boundary List1 = Domain Interface 1 Side 1
Boundary List2 = Domain Interface 1 Side 2
Interface Type = Fluid Fluid
INTERFACE MODELS:
Option = General Connection
FRAME CHANGE:
Option = Frozen Rotor
END
MASS AND MOMENTUM:
Option = Conservative Interface Flux
MOMENTUM INTERFACE MODEL:
Option = None
END
END
PITCH CHANGE:
Option = Value
Pitch Ratio = 1
END
END
MESH CONNECTION:
Option = GGI
END
END
DOMAIN INTERFACE: Domain Interface 2
Boundary List1 = Domain Interface 2 Side 1
Boundary List2 = Domain Interface 2 Side 2
Interface Type = Fluid Fluid
INTERFACE MODELS:
Option = General Connection
FRAME CHANGE:
Option = Frozen Rotor
END
MASS AND MOMENTUM:
Option = Conservative Interface Flux
MOMENTUM INTERFACE MODEL:
Option = None
END
END
PITCH CHANGE:
Option = Value
Pitch Ratio = 1
END
END
MESH CONNECTION:
Option = GGI
END
END
OUTPUT CONTROL:
RESULTS:
File Compression Level = Default
Option = Standard
END
END
SOLVER CONTROL:
Turbulence Numerics = First Order
ADVECTION SCHEME:
Option = High Resolution
END
CONVERGENCE CONTROL:
Maximum Number of Iterations = 1000
Minimum Number of Iterations = 1
Physical Timescale = 4.16667e-006 [s]
Timescale Control = Physical Timescale
END
CONVERGENCE CRITERIA:
Residual Target = 1.E-4
Residual Type = RMS
END
DYNAMIC MODEL CONTROL:
Global Dynamic Model Control = On
END
END
END
COMMAND FILE:
Version = 14.0
Results Version = 14.0
END
SIMULATION CONTROL:
EXECUTION CONTROL:
EXECUTABLE SELECTION:
Double Precision = Off
END
INTERPOLATOR STEP CONTROL:
Runtime Priority = Standard
MEMORY CONTROL:
Memory Allocation Factor = 1.0
END
END
PARALLEL HOST LIBRARY:
HOST DEFINITION: rolandopc
Remote Host Name = ROLANDO-PC
Host Architecture String = winnt-amd64
Installation Root = C:\Program Files\ANSYS Inc\v%v\CFX
END
END
PARTITIONER STEP CONTROL:
Multidomain Option = Independent Partitioning
Runtime Priority = Standard
EXECUTABLE SELECTION:
Use Large Problem Partitioner = Off
END
MEMORY CONTROL:
Memory Allocation Factor = 1.0
END
PARTITIONING TYPE:
MeTiS Type = k-way
Option = MeTiS
Partition Size Rule = Automatic
END
END
RUN DEFINITION:
Run Mode = Full
Solver Input File = C:\Users\Rolando\Desktop\Ansys\Teste\TesteGeral.de f
END
SOLVER STEP CONTROL:
Runtime Priority = Standard
MEMORY CONTROL:
Memory Allocation Factor = 1.0
END
PARALLEL ENVIRONMENT:
Number of Processes = 1
Start Method = Serial
END
END
END
END

RPFigueiredo · October 28, 2014, 04:59

+--------------------------------------------------------------------+
| |
| Solver |
| |
+--------------------------------------------------------------------+

+--------------------------------------------------------------------+
| |
| ANSYS(R) CFX(R) Solver 14.0 |
| |
| Version 2011.10.10-23.01 Tue Oct 11 00:28:38 GMTDT 2011 |
| |
| Executable Attributes |
| |
| single-int32-64bit-novc8-noifort-novc6-optimised-supfort-noprof-nos|
| |
| (C) 2011 ANSYS, Inc. |
| |
| All rights reserved. Unauthorized use, distribution or duplication |
| is prohibited. This product is subject to U.S. laws governing |
| export and re-export. For full Legal Notice, see documentation. |
+--------------------------------------------------------------------+

+--------------------------------------------------------------------+
| Job Information |
+--------------------------------------------------------------------+

Run mode: serial run

Host computer: ROLANDO-PC (PID:2392)
Job started: Tue Oct 28 07:56:08 2014
License Cap: ANSYS CFX Solver (Max 512K Nodes)
License Cap: Multiple Reference Frames
License ID: ROLANDO-PC-SISTEMA-2200-006901

+--------------------------------------------------------------------+
| Memory Allocated for Run (Actual usage may be less) |
+--------------------------------------------------------------------+

Data Type Kwords Words/Node Words/Elem Kbytes Bytes/Node

Real 123622.1 369.02 94.51 482899.0 1476.09
Integer 42063.1 125.56 32.16 164308.8 502.25
Character 3695.0 11.03 2.82 3608.4 11.03
Logical 80.0 0.24 0.06 312.5 0.96
Double 1208.1 3.61 0.92 9438.1 28.85

+--------------------------------------------------------------------+
| Mesh Statistics |
+--------------------------------------------------------------------+
| Domain Name | Orthog. Angle | Exp. Factor | Aspect Ratio |
+----------------------+---------------+--------------+--------------+
| | Minimum [deg] | Maximum | Maximum |
+----------------------+---------------+--------------+--------------+
| Anel | 78.8 OK | 5 OK | 3 OK |
| Duto | 85.1 OK | 1 OK | 4 OK |
| Impelidor | 30.5 ok | 59 ! | 5 OK |
| Global | 30.5 ok | 59 ! | 5 OK |
+----------------------+---------------+--------------+--------------+
| | %! %ok %OK | %! %ok %OK | %! %ok %OK |
+----------------------+---------------+--------------+--------------+
| Anel | 0 0 100 | 0 0 100 | 0 0 100 |
| Duto | 0 0 100 | 0 0 100 | 0 0 100 |
| Impelidor | 0 <1 100 | <1 3 97 | 0 0 100 |
| Global | 0 <1 100 | <1 2 98 | 0 0 100 |
+----------------------+---------------+--------------+--------------+

Domain Name : Anel

Total Number of Nodes = 27616

Total Number of Elements = 22162
Total Number of Prisms = 434
Total Number of Hexahedrons = 21728

Total Number of Faces = 10770

Domain Name : Duto

Total Number of Nodes = 87360

Total Number of Elements = 79560
Total Number of Hexahedrons = 79560

Total Number of Faces = 15360

Domain Name : Impelidor

Total Number of Nodes = 220022

Total Number of Elements = 1206269
Total Number of Tetrahedrons = 1206269

Total Number of Faces = 73106

Global Statistics :

Global Number of Nodes = 334998

Global Number of Elements = 1307991
Total Number of Tetrahedrons = 1206269
Total Number of Prisms = 434
Total Number of Hexahedrons = 101288

Global Number of Faces = 99236

Domain Interface Name : Domain Interface 1

Discretization type = GGI
Intersection type = Direct
Non-overlap area fraction on side 1 = 3.65E-05
Non-overlap area fraction on side 2 = 1.16E-01
Pitch ratio ( user specified ) = 1.000
Pitch angle for side 1 [degrees] = 360.000
Pitch angle for side 2 [degrees] = 360.000

Domain Interface Name : Domain Interface 2

Discretization type = GGI
Intersection type = Direct
Non-overlap area fraction on side 1 = 7.04E-05
Non-overlap area fraction on side 2 = 1.47E-01
Pitch ratio ( user specified ) = 1.000
Pitch angle for side 1 [degrees] = 296.760
Pitch angle for side 2 [degrees] = 360.000

+--------------------------------------------------------------------+
| ERROR #001100279 has occurred in subroutine ErrAction. |
| Message: |
| Floating point exception: Overflow |
| |
| |
| |
| |
| |
+--------------------------------------------------------------------+

+--------------------------------------------------------------------+
| ERROR #001100279 has occurred in subroutine ErrAction. |
| Message: |
| Stopped in routine FPX: C_FPX_HANDLER |
| |
| |
| |
| |
| |
+--------------------------------------------------------------------+

+--------------------------------------------------------------------+
| An error has occurred in cfx5solve: |
| |
| The ANSYS CFX solver exited with return code 1. No results file |
| has been created. |
+--------------------------------------------------------------------+

End of solution stage.

+--------------------------------------------------------------------+
| The following user files have been saved in the directory |
| C:\Users\Rolando\Desktop\Ansys\Teste\TesteGeral_00 1: |
| |
| mon |
+--------------------------------------------------------------------+

This run of the ANSYS CFX Solver has finished.

October 27, 2014, 09:19	Setting rotating frame of referece.	#1
RPFigueiredo Member Rolando Figueiredo Join Date: Mar 2013 Posts: 41 Rep Power: 13	Hello! I'd like to ask a few insights on my setup for a rotating impeller,as seen on the image: http://s13.postimg.org/hzakt4dmf/image.jpg Let's go over each domain and boundaries/interfaces: DOMAIN ANEL Continuous fluid, 1MPa reference pressure, Stationary, Shear Stress Transport Anel_walls: non slip smooth wall Outlet: Average static pressure 7.6MPa/PPres. Profile Blend 0.05 Domain interface 2 side 2: interface, conservative interface flux DOMAIN DUTO Continuous fluid, 1MPa reference pressure, Stationary, Shear Stress Transport Duto_walls: non slip smooth wall Inlet: Mass Flow rate 14kg/s/Normal to boundary/Zero gradient turbulence Domain interface 1 side 1: Conservatice Interface Flux DOMAIN IMPELIDOR Continuous fluid, Reference 1MPa, Rotating -24000rpm about global Y Domain interface 1 side 2: conservative interface flux Domain interface 2 side 2: conservative interface flux Imp_walls: Frame type rotating, no slip smooth wall INTERFACES Domain interface 1: General connection, Frozen rotor, Pitch ratio 1 Domain interface 2: General connection, Frozen rotor, Pitch ratio 1 About solver control, timestep is set to physical, 4.167e-6s. So, is there something too wrong? bacause the solver refuses to run over iteration 1! Any input would be appreciated. Thank you in advance!

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[snappyHexMesh] determining displacement for added points	CFDnewbie147	OpenFOAM Meshing & Mesh Conversion	1	October 22, 2013 09:53
Different solutions for Rotating Reference Frame	fafou09	FLUENT	1	July 24, 2012 10:06
Cells with t below lower limit	Purushothama	Siemens	2	May 31, 2010 21:58
question about governing equation in CFX using rotating/non rotating reference frame	rystokes	CFX	0	January 12, 2010 06:14
Warning 097-	AB	Siemens	6	November 15, 2004 04:41

October 27, 2014, 16:25		#2
ghorrocks Super Moderator Glenn Horrocks Join Date: Mar 2009 Location: Sydney, Australia Posts: 17,703 Rep Power: 143	Please post your output file. Also note that it appears you could model this with a single rotating domain, and no stationary domains. Then there is no need for interfaces.

October 28, 2014, 04:58		#3
RPFigueiredo Member Rolando Figueiredo Join Date: Mar 2013 Posts: 41 Rep Power: 13	I realize I could avoid the interfaces. I tried it with the single RFR, but it wouldn't work, so I added the stationary as I will eventually have to model the volute (once I figure out the issue). Here's the out file: This run of the CFX-14.0 Solver started at 07:56:04 on 28 Oct 2014 by user Rolando on ROLANDO-PC (intel_xeon64.sse2_winnt) using the command: "C:\Program Files\ANSYS Inc\v140\CFX\bin\perllib\cfx5solve.pl" -stdout-comms -batch -ccl - Setting up CFX Solver run ... +--------------------------------------------------------------------+ \| \| \| CFX Command Language for Run \| \| \| +--------------------------------------------------------------------+ LIBRARY: MATERIAL: Water Material Description = Water (liquid) Material Group = Water Data, Constant Property Liquids Option = Pure Substance Thermodynamic State = Liquid PROPERTIES: Option = General Material EQUATION OF STATE: Density = 997.0 [kg m^-3] Molar Mass = 18.02 [kg kmol^-1] Option = Value END SPECIFIC HEAT CAPACITY: Option = Value Specific Heat Capacity = 4181.7 [J kg^-1 K^-1] Specific Heat Type = Constant Pressure END REFERENCE STATE: Option = Specified Point Reference Pressure = 1 [atm] Reference Specific Enthalpy = 0.0 [J/kg] Reference Specific Entropy = 0.0 [J/kg/K] Reference Temperature = 25 [C] END DYNAMIC VISCOSITY: Dynamic Viscosity = 8.899E-4 [kg m^-1 s^-1] Option = Value END THERMAL CONDUCTIVITY: Option = Value Thermal Conductivity = 0.6069 [W m^-1 K^-1] END ABSORPTION COEFFICIENT: Absorption Coefficient = 1.0 [m^-1] Option = Value END SCATTERING COEFFICIENT: Option = Value Scattering Coefficient = 0.0 [m^-1] END REFRACTIVE INDEX: Option = Value Refractive Index = 1.0 [m m^-1] END THERMAL EXPANSIVITY: Option = Value Thermal Expansivity = 2.57E-04 [K^-1] END END END END FLOW: Flow Analysis 1 SOLUTION UNITS: Angle Units = [rad] Length Units = [m] Mass Units = [kg] Solid Angle Units = [sr] Temperature Units = [K] Time Units = [s] END ANALYSIS TYPE: Option = Steady State EXTERNAL SOLVER COUPLING: Option = None END END DOMAIN: Anel Coord Frame = Coord 0 Domain Type = Fluid Location = LIVE BOUNDARY: Anel_walls Boundary Type = WALL Location = WALLS 2 BOUNDARY CONDITIONS: MASS AND MOMENTUM: Option = No Slip Wall END WALL ROUGHNESS: Option = Smooth Wall END END END BOUNDARY: Domain Interface 2 Side 2 Boundary Type = INTERFACE Location = INLET 2 BOUNDARY CONDITIONS: MASS AND MOMENTUM: Option = Conservative Interface Flux END TURBULENCE: Option = Conservative Interface Flux END END END BOUNDARY: Outlet Boundary Type = OUTLET Location = OUTLET 2 BOUNDARY CONDITIONS: FLOW REGIME: Option = Subsonic END MASS AND MOMENTUM: Option = Average Static Pressure Pressure Profile Blend = 0.05 Relative Pressure = 7.6 [MPa] END PRESSURE AVERAGING: Option = Average Over Whole Outlet END END END DOMAIN MODELS: BUOYANCY MODEL: Option = Non Buoyant END DOMAIN MOTION: Option = Stationary END MESH DEFORMATION: Option = None END REFERENCE PRESSURE: Reference Pressure = 1 [MPa] END END FLUID DEFINITION: Fluid 1 Material = Water Option = Material Library MORPHOLOGY: Option = Continuous Fluid END END FLUID MODELS: COMBUSTION MODEL: Option = None END HEAT TRANSFER MODEL: Fluid Temperature = 25 [C] Option = Isothermal END THERMAL RADIATION MODEL: Option = None END TURBULENCE MODEL: Option = k epsilon END TURBULENT WALL FUNCTIONS: Option = Scalable END END END DOMAIN: Duto Coord Frame = Coord 0 Domain Type = Fluid Location = SOLID BOUNDARY: Domain Interface 1 Side 1 Boundary Type = INTERFACE Location = OUTLET BOUNDARY CONDITIONS: MASS AND MOMENTUM: Option = Conservative Interface Flux END TURBULENCE: Option = Conservative Interface Flux END END END BOUNDARY: Duto_walls Boundary Type = WALL Location = WALLS BOUNDARY CONDITIONS: MASS AND MOMENTUM: Option = No Slip Wall END WALL ROUGHNESS: Option = Smooth Wall END END END BOUNDARY: Inlet Boundary Type = INLET Location = INLET BOUNDARY CONDITIONS: FLOW DIRECTION: Option = Normal to Boundary Condition END FLOW REGIME: Option = Subsonic END MASS AND MOMENTUM: Mass Flow Rate = 14.027 [kg s^-1] Option = Mass Flow Rate END TURBULENCE: Option = Zero Gradient END END END DOMAIN MODELS: BUOYANCY MODEL: Option = Non Buoyant END DOMAIN MOTION: Option = Stationary END MESH DEFORMATION: Option = None END REFERENCE PRESSURE: Reference Pressure = 1 [MPa] END END FLUID DEFINITION: Fluid 1 Material = Water Option = Material Library MORPHOLOGY: Option = Continuous Fluid END END FLUID MODELS: COMBUSTION MODEL: Option = None END HEAT TRANSFER MODEL: Fluid Temperature = 25 [C] Option = Isothermal END THERMAL RADIATION MODEL: Option = None END TURBULENCE MODEL: Option = k epsilon END TURBULENT WALL FUNCTIONS: Option = Scalable END END END DOMAIN: Impelidor Coord Frame = Coord 0 Domain Type = Fluid Location = CREATED_MATERIAL_10 BOUNDARY: Domain Interface 1 Side 2 Boundary Type = INTERFACE Location = INLET 3 BOUNDARY CONDITIONS: MASS AND MOMENTUM: Option = Conservative Interface Flux END TURBULENCE: Option = Conservative Interface Flux END END END BOUNDARY: Domain Interface 2 Side 1 Boundary Type = INTERFACE Location = OUTLET 3 BOUNDARY CONDITIONS: MASS AND MOMENTUM: Option = Conservative Interface Flux END TURBULENCE: Option = Conservative Interface Flux END END END BOUNDARY: Imp_walls Boundary Type = WALL Frame Type = Rotating Location = WALLS 3 BOUNDARY CONDITIONS: MASS AND MOMENTUM: Option = No Slip Wall END WALL ROUGHNESS: Option = Smooth Wall END END END DOMAIN MODELS: BUOYANCY MODEL: Option = Non Buoyant END DOMAIN MOTION: Angular Velocity = -24000 [rev min^-1] Option = Rotating AXIS DEFINITION: Option = Coordinate Axis Rotation Axis = Coord 0.2 END END MESH DEFORMATION: Option = None END REFERENCE PRESSURE: Reference Pressure = 1 [MPa] END END FLUID DEFINITION: Fluid 1 Material = Water Option = Material Library MORPHOLOGY: Option = Continuous Fluid END END FLUID MODELS: COMBUSTION MODEL: Option = None END HEAT TRANSFER MODEL: Fluid Temperature = 25 [C] Option = Isothermal END THERMAL RADIATION MODEL: Option = None END TURBULENCE MODEL: Option = k epsilon END TURBULENT WALL FUNCTIONS: Option = Scalable END END END DOMAIN INTERFACE: Domain Interface 1 Boundary List1 = Domain Interface 1 Side 1 Boundary List2 = Domain Interface 1 Side 2 Interface Type = Fluid Fluid INTERFACE MODELS: Option = General Connection FRAME CHANGE: Option = Frozen Rotor END MASS AND MOMENTUM: Option = Conservative Interface Flux MOMENTUM INTERFACE MODEL: Option = None END END PITCH CHANGE: Option = Value Pitch Ratio = 1 END END MESH CONNECTION: Option = GGI END END DOMAIN INTERFACE: Domain Interface 2 Boundary List1 = Domain Interface 2 Side 1 Boundary List2 = Domain Interface 2 Side 2 Interface Type = Fluid Fluid INTERFACE MODELS: Option = General Connection FRAME CHANGE: Option = Frozen Rotor END MASS AND MOMENTUM: Option = Conservative Interface Flux MOMENTUM INTERFACE MODEL: Option = None END END PITCH CHANGE: Option = Value Pitch Ratio = 1 END END MESH CONNECTION: Option = GGI END END OUTPUT CONTROL: RESULTS: File Compression Level = Default Option = Standard END END SOLVER CONTROL: Turbulence Numerics = First Order ADVECTION SCHEME: Option = High Resolution END CONVERGENCE CONTROL: Maximum Number of Iterations = 1000 Minimum Number of Iterations = 1 Physical Timescale = 4.16667e-006 [s] Timescale Control = Physical Timescale END CONVERGENCE CRITERIA: Residual Target = 1.E-4 Residual Type = RMS END DYNAMIC MODEL CONTROL: Global Dynamic Model Control = On END END END COMMAND FILE: Version = 14.0 Results Version = 14.0 END SIMULATION CONTROL: EXECUTION CONTROL: EXECUTABLE SELECTION: Double Precision = Off END INTERPOLATOR STEP CONTROL: Runtime Priority = Standard MEMORY CONTROL: Memory Allocation Factor = 1.0 END END PARALLEL HOST LIBRARY: HOST DEFINITION: rolandopc Remote Host Name = ROLANDO-PC Host Architecture String = winnt-amd64 Installation Root = C:\Program Files\ANSYS Inc\v%v\CFX END END PARTITIONER STEP CONTROL: Multidomain Option = Independent Partitioning Runtime Priority = Standard EXECUTABLE SELECTION: Use Large Problem Partitioner = Off END MEMORY CONTROL: Memory Allocation Factor = 1.0 END PARTITIONING TYPE: MeTiS Type = k-way Option = MeTiS Partition Size Rule = Automatic END END RUN DEFINITION: Run Mode = Full Solver Input File = C:\Users\Rolando\Desktop\Ansys\Teste\TesteGeral.de f END SOLVER STEP CONTROL: Runtime Priority = Standard MEMORY CONTROL: Memory Allocation Factor = 1.0 END PARALLEL ENVIRONMENT: Number of Processes = 1 Start Method = Serial END END END END

October 28, 2014, 04:59		#4
RPFigueiredo Member Rolando Figueiredo Join Date: Mar 2013 Posts: 41 Rep Power: 13	+--------------------------------------------------------------------+ \| \| \| Solver \| \| \| +--------------------------------------------------------------------+ +--------------------------------------------------------------------+ \| \| \| ANSYS(R) CFX(R) Solver 14.0 \| \| \| \| Version 2011.10.10-23.01 Tue Oct 11 00:28:38 GMTDT 2011 \| \| \| \| Executable Attributes \| \| \| \| single-int32-64bit-novc8-noifort-novc6-optimised-supfort-noprof-nos\| \| \| \| (C) 2011 ANSYS, Inc. \| \| \| \| All rights reserved. Unauthorized use, distribution or duplication \| \| is prohibited. This product is subject to U.S. laws governing \| \| export and re-export. For full Legal Notice, see documentation. \| +--------------------------------------------------------------------+ +--------------------------------------------------------------------+ \| Job Information \| +--------------------------------------------------------------------+ Run mode: serial run Host computer: ROLANDO-PC (PID:2392) Job started: Tue Oct 28 07:56:08 2014 License Cap: ANSYS CFX Solver (Max 512K Nodes) License Cap: Multiple Reference Frames License ID: ROLANDO-PC-SISTEMA-2200-006901 +--------------------------------------------------------------------+ \| Memory Allocated for Run (Actual usage may be less) \| +--------------------------------------------------------------------+ Data Type Kwords Words/Node Words/Elem Kbytes Bytes/Node Real 123622.1 369.02 94.51 482899.0 1476.09 Integer 42063.1 125.56 32.16 164308.8 502.25 Character 3695.0 11.03 2.82 3608.4 11.03 Logical 80.0 0.24 0.06 312.5 0.96 Double 1208.1 3.61 0.92 9438.1 28.85 +--------------------------------------------------------------------+ \| Mesh Statistics \| +--------------------------------------------------------------------+ \| Domain Name \| Orthog. Angle \| Exp. Factor \| Aspect Ratio \| +----------------------+---------------+--------------+--------------+ \| \| Minimum [deg] \| Maximum \| Maximum \| +----------------------+---------------+--------------+--------------+ \| Anel \| 78.8 OK \| 5 OK \| 3 OK \| \| Duto \| 85.1 OK \| 1 OK \| 4 OK \| \| Impelidor \| 30.5 ok \| 59 ! \| 5 OK \| \| Global \| 30.5 ok \| 59 ! \| 5 OK \| +----------------------+---------------+--------------+--------------+ \| \| %! %ok %OK \| %! %ok %OK \| %! %ok %OK \| +----------------------+---------------+--------------+--------------+ \| Anel \| 0 0 100 \| 0 0 100 \| 0 0 100 \| \| Duto \| 0 0 100 \| 0 0 100 \| 0 0 100 \| \| Impelidor \| 0 <1 100 \| <1 3 97 \| 0 0 100 \| \| Global \| 0 <1 100 \| <1 2 98 \| 0 0 100 \| +----------------------+---------------+--------------+--------------+ Domain Name : Anel Total Number of Nodes = 27616 Total Number of Elements = 22162 Total Number of Prisms = 434 Total Number of Hexahedrons = 21728 Total Number of Faces = 10770 Domain Name : Duto Total Number of Nodes = 87360 Total Number of Elements = 79560 Total Number of Hexahedrons = 79560 Total Number of Faces = 15360 Domain Name : Impelidor Total Number of Nodes = 220022 Total Number of Elements = 1206269 Total Number of Tetrahedrons = 1206269 Total Number of Faces = 73106 Global Statistics : Global Number of Nodes = 334998 Global Number of Elements = 1307991 Total Number of Tetrahedrons = 1206269 Total Number of Prisms = 434 Total Number of Hexahedrons = 101288 Global Number of Faces = 99236 Domain Interface Name : Domain Interface 1 Discretization type = GGI Intersection type = Direct Non-overlap area fraction on side 1 = 3.65E-05 Non-overlap area fraction on side 2 = 1.16E-01 Pitch ratio ( user specified ) = 1.000 Pitch angle for side 1 [degrees] = 360.000 Pitch angle for side 2 [degrees] = 360.000 Domain Interface Name : Domain Interface 2 Discretization type = GGI Intersection type = Direct Non-overlap area fraction on side 1 = 7.04E-05 Non-overlap area fraction on side 2 = 1.47E-01 Pitch ratio ( user specified ) = 1.000 Pitch angle for side 1 [degrees] = 296.760 Pitch angle for side 2 [degrees] = 360.000 +--------------------------------------------------------------------+ \| ERROR #001100279 has occurred in subroutine ErrAction. \| \| Message: \| \| Floating point exception: Overflow \| \| \| \| \| \| \| \| \| \| \| +--------------------------------------------------------------------+ +--------------------------------------------------------------------+ \| ERROR #001100279 has occurred in subroutine ErrAction. \| \| Message: \| \| Stopped in routine FPX: C_FPX_HANDLER \| \| \| \| \| \| \| \| \| \| \| +--------------------------------------------------------------------+ +--------------------------------------------------------------------+ \| An error has occurred in cfx5solve: \| \| \| \| The ANSYS CFX solver exited with return code 1. No results file \| \| has been created. \| +--------------------------------------------------------------------+ End of solution stage. +--------------------------------------------------------------------+ \| The following user files have been saved in the directory \| \| C:\Users\Rolando\Desktop\Ansys\Teste\TesteGeral_00 1: \| \| \| \| mon \| +--------------------------------------------------------------------+ This run of the ANSYS CFX Solver has finished.