Error: Stopped in routine MEMERR
 

Hi,

I am trying to do a thermal comfort simulation in an office. Analysis type is steady state. The office has 7 rooms as shown in the picture. First I just simulated 2 rooms and I did not get errors. Then I made the other rooms and I got the following error message. There are air conditioners in every room. The model include thermal radiation on the window boundaries. I use ANSYS 16.0.
Can anybody help me with this error?



Couldn't initialise lpnquery library
+--------------------------------------------------------------------+
| |
| Partitioning |
| |
+--------------------------------------------------------------------+




+--------------------------------------------------------------------+
| |
| ANSYS(R) CFX(R) Partitioner |
| |
| Release 16.0 |
| Build 16.0 2014.11.14-23.10-133146 |
| Sat Nov 15 00:24:02 GMTST 2014 |
| |
| Executable Attributes |
| |
| double-64bit-int32-supfort-optimised-noprof-lcomp |
| |
| (C) 2014 ANSYS, Inc. |
| |
| All rights reserved. Unauthorized use, distribution or duplication |
| is prohibited. This product is subject to U.S. laws governing |
| export and re-export. For full Legal Notice, see documentation. |
+--------------------------------------------------------------------+




+--------------------------------------------------------------------+
| Job Information at Start of Run |
+--------------------------------------------------------------------+

Run mode: partitioning run

Host computer: CLUSTER03 (PID:3516)

Job started: Mon Jul 27 10:55:00 2015

Details of error:-
----------------
Error detected by routine PEEKI
CDANAM = /LPNQ/DB/NREG
CRESLT = NONE

Current Directory : /FLOW/REGMAP

+================================================= ===================+
| ****** PROBLEM REPORT ****** |
|--------------------------------------------------------------------|
| Subsystem: Input and Output |
| Subroutine name: ErrAction |
| Severity level: Fatal Error |
| Error message number: 001100279 |
|--------------------------------------------------------------------|
| Message: |
| |
| Stopped in routine MEMERR |
| |
| |
| |
| |
| |
+================================================= ===================+

+--------------------------------------------------------------------+
| An error has occurred in cfx5solve: |
| |
| The ANSYS CFX partitioner exited with return code 1. |
+--------------------------------------------------------------------+

Looks like the partitioner ran out of memory. Try using the large simulation partitioner.

I tried now but I get the same error.

There are plenty of other options to try. Try different partitioning algorithms. Also read the documentation on the command line options for available options with the partitioner.

How many nodes is this mesh?

Nodes: 4080647
Elements: 14351488

That is not a large simulation. There is some other problem with your simulation setup. A moderate size model like that should partition fine. I would check your simulation setup.

Simulation setup:

Not sure how you obtained your definition file, a previous version ?

From the message, the software is failing when accessing the database (DB) for the definition of mesh regions (REG MAP).

Does it fail if you try to run in serial mode ?

Hope the above helps,

Thanks for the help so far, but it also fails in serial mode.

From your CFX_001.out, the message says it all

Something must be wrong with the definition file. Try writing a new definition file, or re-importing the mesh.

Error detected by routine PEEKCA , MEMERR
 

Hello,

I am trying to solve FT TRb rotor-stator case for flutter analysis. In past every thing was good. but recently I am getting this error.

+--------------------------------------------------------------------+
| Host Memory Information (Mbytes) |
+--------------------------------------------------------------------+
| Host | Npart | System | Allocated | % |
+------------------------+-------+-------------+-------------+-------+
| orwell.encs.concordia.c| 39 | 160988.86 | 93994.26 | 58.39 |
+------------------------+-------+-------------+-------------+-------+

Details of error:-
----------------
Error detected by routine PEEKCA
CDANAM = CPERIOD
CRESLT = NONE

Current Directory : /ABR/OUTPUT/ZN2

+--------------------------------------------------------------------+
| ERROR #001100279 has occurred in subroutine ErrAction. |
| Message: |
| Stopped in routine MEMERR |
| |
| |
| |
| |
| |
+--------------------------------------------------------------------+

+--------------------------------------------------------------------+
| An error has occurred in cfx5solve: |
| |
| The ANSYS CFX solver exited with return code 1. No results file |
| has been created. |
+--------------------------------------------------------------------+

End of solution stage.

+--------------------------------------------------------------------+
| The following user files have been saved in the directory |
| /nfs/private/k/kaushal/p_mittal/Test2/Flutter_blade_only/2s_2r_v4- |
| _blade_only_978k_elm_HB_nd0_pout101325_001: |
| |
| pids, trace |
+--------------------------------------------------------------------+


This run of the ANSYS CFX Solver has finished.


I had trying multiple things like increasing memory over riding memory etc.. tried in serial mode, but same results. can anyone help suggest me anything, please?

Please do not PM me with copies of posts on the forum. I find that extremely rude.

Reference to another topic that helped me
 

I had the same Error-Message and tried many things with no effect until i found that other topic. For me it was a hidden "ä" in a Sectionname which I completely oversaw :D Maybe the last answer there can help others too. -> https://www.cfd-online.com/Forums/cf...ery-error.html

Hello
Try using serial mode
And i have a question how many finite element have Ur model ???