CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums > Software User Forums > ANSYS > CFX

On gravity modelling...

Register Blogs Members List Search Today's Posts Mark Forums Read

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old   November 20, 2001, 06:42
Default On gravity modelling...
  #1
Drona
Guest
 
Posts: n/a
Hello everyone,

I have been reading with interest all the posts on effects of gravity and its modelling by CFX. I had posted a similar topic earlier. What I understood from the discussion was one doesn't need to be worried about gravity if the flow is single phase, and there are no temperature and density variations. I understood that CXF(I assume all the solvers TASCflow, CFX 5, 4) takes care of it and adjusts the pressure. I also read somewhere that for a gravity driven flow, one needs to add the pressure due to gravity(rho*g*h) to the pressure as solved by the code. I was a bit confused, and thought should write to this forum. If it takes care of gravity, how one should tell the code which way the gravity acts? I know if we use the buoyancy models, there is a place where we can specify the vectors, but I am not talking about buoyancy as there are no temperature or density variations in my flow which is, you guessed it, gravity driven.

Thanks and looking forward to hearing from you

Drona
  Reply With Quote

Old   November 20, 2001, 18:26
Default Re: On gravity modelling...
  #2
P.Fonteijn
Guest
 
Posts: n/a
1) What is your question/point?

2) You don't have to add rho*g*h. Previous discussions have made that clear.

Pascale Fonteijn
  Reply With Quote

Old   November 20, 2001, 21:37
Default Re: On gravity modelling...
  #3
Robin Steed
Guest
 
Posts: n/a
Hi Drona,

If your flow is gravity driven, there must be a density variation or multiple phases involved. Otherwise there is no force to drive the fluid.

What is the problem you are trying to solve?

Robin
  Reply With Quote

Old   November 21, 2001, 05:44
Default Re: On gravity modelling...
  #4
Drona
Guest
 
Posts: n/a
Response to Pascale and Robin'n postings;

My problem is a water turbine. There is no density difference(at least not significant- i assume it's incompressible flow and no temperature variations either) and there is only one phase(liquid - at least that's the assumption I make for water flow). But water does flow. So are my assumptions wrong? I seem to be terribly confused here.

I want to simplify my question/point: How can I get the TASCflow to take into account the level difference (inlet at a higher level that outlet - normal for any water turbine case) withought having to use pressure difference based boundary conditions? I want to use mass flow as inlet condition to meet the design criteria.

Pacale, you say you don't need to add rho*g*h. But I quote the following from the discussions in this forum. It was in turn quoted from one of CFX manuals.

"Note that the Results File does not contain the hydrostatic contribution to pressure, and this should be added to obtain actual values of pressure relative to the Reference Pressure in these cases". I should be terribly mistaken somewhere.

Sorry, it's become a long messege again. I find it difficult to explain in very short messege. I am not sure if I am able to explain my problem.

Thanks for your responses and looking forward to hearing from you

Drona
  Reply With Quote

Old   November 21, 2001, 22:36
Default Re: On gravity modelling...
  #5
Robin Steed
Guest
 
Posts: n/a
Hi Drona,

You will not require buoyancy to model your flow through the turbine unless you are modeling cavitation (which implies a density/phase variation). You don't need the hydrostatic pressure contribution because it will not affect the turbine performance (again, unless you are accounting for cavitation).

To account for the level difference, set the total pressure at the inlet equal to...

<bi>PtotalIn = rho*g*(h_inlet - h_outlet) + PstaticOut</bi>

use an average static pressure outlet set to PstaticOut. This will give you the correct pressure drop to drive your flow.

When you post process your results, you may prefer to see the hydrostatic pressure included. The following TASCtool command will create the pressure field.

(assuming z is up and ZREF is a reference height of your choosing)

calc P_HYDROSTATIC = P + RHO*G*(ZREF-Z)

This will create a new scalar, P_HYDROSTATIC, which you may post-process to all your hearts desire.

Best regards, Robin
  Reply With Quote

Old   November 22, 2001, 05:21
Default Re: On gravity modelling...
  #6
Drona
Guest
 
Posts: n/a
Hi Robin,

Thanks for the suggestion. I may have to add additional pressure due to velocity at the inlet(rho*v*v/2), as the acual inlet(which I am not modelling) is further away at a higher level(but is only contains a pipe, which can be calculated manually) and water is already at a certain velocity. That way I can also constrain the mass flow I guess. So I might have to add more rho*g*h(h is the additional height). Am I right?

Also, do I put PstaticOut as zero, because it opens to atmosphere?

Thanks a lot

Drona

  Reply With Quote

Old   November 22, 2001, 09:34
Default Re: On gravity modelling...
  #7
Robin Steed
Guest
 
Posts: n/a
Drona,

If you use the total pressure as I suggested, the inlet dynamics will already be included. If you have an additional length of pipe preceding your inlet you can account for it by providing the necessary drop in total pressure.

As for the velocity at the inlet, if your mass flow is constrained, then you will want to use a mass flow (or velocity) specified inlet or outlet (mass flow outlet is usually better than inlet).

If you are running Ptotal in -> Pstatic out, the important thing is the pressure drop. If you add atmospheric pressure to your outlet, just make sure you do the same to your inlet.

Remember: It's all relative!

Regards, Robin
  Reply With Quote

Old   November 22, 2001, 11:28
Default Re: On gravity modelling...
  #8
Drona
Guest
 
Posts: n/a
Thanks Robin,

I will try to solve the problem and see what I get. I will let you know.

Thanks again for help. I may come back with more questions though!

Drona
  Reply With Quote

Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
gravity current modelling asistas FLUENT 10 September 24, 2011 23:43
Urgent....Help on modelling variable gravity sabbasi_mr Main CFD Forum 0 December 2, 2009 01:03
how to consider gravity in CFX shrimp CFX 4 September 8, 2008 21:41
Help: gravity in CFX Dejun Jing CFX 2 July 22, 2002 09:58
Gravity modelling Drona CFX 7 August 10, 2001 08:00


All times are GMT -4. The time now is 21:48.