Flow in an Axial Rotor /Stator -Ansys CFX Tutorials

amiza83 · July 3, 2017, 00:16

Hi all,

I am new in using CFX.I am currently working on Ansys CFX Tutorial No.14 - Flow in an Axial Rotor /Stator.

During working on this tutorial for obtaining a solution to the frozen Rotor Model, an error occurred in cfx5solve. A dialog box appear stating that

''The ANSYS CFX solver exited with return code 1. No results file has been
created.

I did run using serial and parallel. But the same note appear during running the simulation.

Could anyone here give an advise to solve my problem

Thanks
Amiza

-Maxim- · July 4, 2017, 02:15

post your complete out-file please. The error message you posted is only part of the complete error.
Alternatively, just delete your progress and start over again. I'm sure there's just a tiny mistake. It'll be quicker if you just re-do it instead of letting us find your mistake...

amiza83 · July 4, 2017, 04:03

Hi Maxim,

I did solved this warning and managed to obtain a solution and successful to view the Simulation Result in CFD Post in Steady and transient state.

Thank a lot for your kind reply

Best Regards

Amiza

-Maxim- · July 4, 2017, 04:11

very good. You could post here what your fix was so that other people that run into the same problem might learn from your mistake

amiza83 · July 4, 2017, 04:22

Yes sure.

Kindly, please refer to the attached solution for this problem.

Thanks again sir.

Best Regards
Amiza

July 3, 2017, 00:16	Flow in an Axial Rotor /Stator -Ansys CFX Tutorials	#1
amiza83 New Member amiza Join Date: Jul 2017 Posts: 3 Rep Power: 8	Hi all, I am new in using CFX.I am currently working on Ansys CFX Tutorial No.14 - Flow in an Axial Rotor /Stator. During working on this tutorial for obtaining a solution to the frozen Rotor Model, an error occurred in cfx5solve. A dialog box appear stating that ''The ANSYS CFX solver exited with return code 1. No results file has been created. I did run using serial and parallel. But the same note appear during running the simulation. Could anyone here give an advise to solve my problem Thanks Amiza

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
About Some Concepts:Laminar flow, turbulent flow, steady flow and time-dependent flow	Jing	Main CFD Forum	8	October 5, 2018 17:02
Review: Reversed flow	CRT	FLUENT	1	May 7, 2018 05:36
Thrust in Axial flow fan for different inlets	acoustica	CFX	8	April 24, 2014 03:44
I want to confirm the performance of the axial flow fan.	Sanghyun - PARK	FloEFD, FloWorks & FloTHERM	1	October 29, 2013 03:22
Fanno flow (pipe flow) in CFX	Saima	CFX	1	December 17, 2012 05:36

July 4, 2017, 02:15		#2
-Maxim- Senior Member Maxim Join Date: Aug 2015 Location: Germany Posts: 415 Rep Power: 12	post your complete out-file please. The error message you posted is only part of the complete error. Alternatively, just delete your progress and start over again. I'm sure there's just a tiny mistake. It'll be quicker if you just re-do it instead of letting us find your mistake...

July 4, 2017, 04:03		#3
amiza83 New Member amiza Join Date: Jul 2017 Posts: 3 Rep Power: 8	Hi Maxim, I did solved this warning and managed to obtain a solution and successful to view the Simulation Result in CFD Post in Steady and transient state. Thank a lot for your kind reply Best Regards Amiza

July 4, 2017, 04:11		#4
-Maxim- Senior Member Maxim Join Date: Aug 2015 Location: Germany Posts: 415 Rep Power: 12	very good. You could post here what your fix was so that other people that run into the same problem might learn from your mistake