y+ contour plot through flow domain

Katha · July 20, 2017, 05:28

Hello,

I was trying to create a contour plot of the yplus value at an arbitrary plane throuh my flow domain.
Therefore what I did is creating the according plane, then creating a contour plot with the beforehand created plane as the location and Yplus as the variable with local/global range.
If I choose any other variable than Yplus - like pressure, density, ... - I see the expected contour plot. Once I pick Yplus the plane/contour simply disappears, whereas I do see the legend with the a value range. (0 to 1.88)

I have naturally checked for tutorials but couldn´t find any fault in my procedure also since it is a pretty basic problem as far as i can tell.

worth mentioning: It is also possible to color a plane directly using a certain variable. This methods results in CFX displaying the according plane in grey colour except very close to the walls which are coloured.

I appreciate any hints regarding this.

Regards, katha

urosgrivc · July 20, 2017, 06:11

Hi

This was a topic meny times here on the forum, so you could search it.
And this is a comon but simple problem to people geting into cfd.

Y+ value only aplies to walls there is no y+ value further from the wals so everithing is grey (no value) but you see values in the first element from the wall this is vhere y+ is relevant and imortant.
So only first element from the wall is coloured.

ghorrocks · July 20, 2017, 06:40

Yes, this question has been asked a few times. Can you add it to the FAQ page? https://www.cfd-online.com/Wiki/Ansys_FAQ

Katha · July 20, 2017, 07:29

hi,

thx for the answers, well I dont know, why I didnt find it. Of course I know, that y+ is a value only relevant to the wall, nevertheless I have used other software before and therefore know, that it is possibly to create such a contour plot in fluent for example.
The reason I was trying to plot it is since I thought it could be useful in optimizing the mesh as it could reduce the number of iterations by knowing that for example my third layer had a ceratin y+ that I desire.
Anyways thank u for the quick reply.

ghorrocks · July 20, 2017, 07:35

If you draw contours of the wall boundary objects rather than the cross section plane you will get a useful plot. I think that is what you are trying to do. You can do this as y+ exists everywhere on a wall boundary, of course.

Katha · July 20, 2017, 07:38

ja, that was the first thing I did of course. As I said my aim was to reduce the amount of times I would have to change the mesh (which is rather large therefore grid generation takes time) by seeing how the y+ looks like in the third/fourth layer and then estimating the according cell height.

July 20, 2017, 05:28	y+ contour plot through flow domain	#1
Katha New Member Join Date: May 2015 Posts: 19 Rep Power: 10	Hello, I was trying to create a contour plot of the yplus value at an arbitrary plane throuh my flow domain. Therefore what I did is creating the according plane, then creating a contour plot with the beforehand created plane as the location and Yplus as the variable with local/global range. If I choose any other variable than Yplus - like pressure, density, ... - I see the expected contour plot. Once I pick Yplus the plane/contour simply disappears, whereas I do see the legend with the a value range. (0 to 1.88) I have naturally checked for tutorials but couldn´t find any fault in my procedure also since it is a pretty basic problem as far as i can tell. worth mentioning: It is also possible to color a plane directly using a certain variable. This methods results in CFX displaying the according plane in grey colour except very close to the walls which are coloured. I appreciate any hints regarding this. Regards, katha

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
mass flow in is not equal to mass flow out	saii	CFX	12	March 19, 2018 05:21
Periodic Pressure drop	cfd_begin	CFX	10	May 25, 2017 07:09
[OpenFOAM] Viewing a scatter plot of points overlayed on my paraFoam flow visualization	karma15	ParaView	1	April 15, 2016 14:17
[blockMesh] Flow domain by BLOCKMESH for plasma induced flow simulation	mukut	OpenFOAM Meshing & Mesh Conversion	0	June 2, 2014 06:19
[DesignModeler] Flow Domain of DesignModeler	swiss_zhang	ANSYS Meshing & Geometry	0	June 9, 2011 07:13

July 20, 2017, 06:11		#2
urosgrivc Senior Member urosgrivc Join Date: Dec 2015 Location: Slovenija Posts: 365 Rep Power: 11	Hi This was a topic meny times here on the forum, so you could search it. And this is a comon but simple problem to people geting into cfd. Y+ value only aplies to walls there is no y+ value further from the wals so everithing is grey (no value) but you see values in the first element from the wall this is vhere y+ is relevant and imortant. So only first element from the wall is coloured.

July 20, 2017, 06:40		#3
ghorrocks Super Moderator Glenn Horrocks Join Date: Mar 2009 Location: Sydney, Australia Posts: 17,703 Rep Power: 143	Yes, this question has been asked a few times. Can you add it to the FAQ page? https://www.cfd-online.com/Wiki/Ansys_FAQ

July 20, 2017, 07:29		#4
Katha New Member Join Date: May 2015 Posts: 19 Rep Power: 10	hi, thx for the answers, well I dont know, why I didnt find it. Of course I know, that y+ is a value only relevant to the wall, nevertheless I have used other software before and therefore know, that it is possibly to create such a contour plot in fluent for example. The reason I was trying to plot it is since I thought it could be useful in optimizing the mesh as it could reduce the number of iterations by knowing that for example my third layer had a ceratin y+ that I desire. Anyways thank u for the quick reply.

July 20, 2017, 07:35		#5
ghorrocks Super Moderator Glenn Horrocks Join Date: Mar 2009 Location: Sydney, Australia Posts: 17,703 Rep Power: 143	If you draw contours of the wall boundary objects rather than the cross section plane you will get a useful plot. I think that is what you are trying to do. You can do this as y+ exists everywhere on a wall boundary, of course.

July 20, 2017, 07:38		#6
Katha New Member Join Date: May 2015 Posts: 19 Rep Power: 10	ja, that was the first thing I did of course. As I said my aim was to reduce the amount of times I would have to change the mesh (which is rather large therefore grid generation takes time) by seeing how the y+ looks like in the third/fourth layer and then estimating the according cell height.