|
[Sponsors] |
How to save Transient statistics in CFX Pre for getting Phase-averaged results |
|
LinkBack | Thread Tools | Search this Thread | Display Modes |
November 28, 2017, 17:09 |
How to save Transient statistics in CFX Pre for getting Phase-averaged results
|
#1 |
New Member
Gopal Krishan
Join Date: Aug 2016
Posts: 5
Rep Power: 9 |
Hey Guys,
I am trying to save phase-averaged results for my simulation and I have tried to save the results by adding the desired timesteps in transient statistics(CFX-PRE) as shown in attached image. But, in the post-processing, it is not showing any phase averaged results or folder. Could you please help me with this? |
|
November 29, 2017, 00:58 |
|
#2 |
Senior Member
urosgrivc
Join Date: Dec 2015
Location: Slovenija
Posts: 365
Rep Power: 11 |
Are you able to make a motor point for this, so you could visualize it vhile solving?
if you are, you can export plot variables directly from solver manager. You can even change properties of arithmetic average in the solver manager if that helps |
|
November 29, 2017, 10:37 |
|
#3 |
Senior Member
Join Date: Jun 2009
Posts: 1,803
Rep Power: 32 |
The transient statistics definition setup is confusing.
If the variables involved in the definitions overlap, you may get unexpected results. The results for a transient statistics are presented as VariableListed.Trnavg for the Arithmetic Average. Say you selected Pressure and Temperature, the results file will have Pressure.Trnavg and Temperature.Trnavg. The Start/End Iteration Lists are used to define the range in time for the calculation of the Arithmetic Average. |
|
November 29, 2017, 15:12 |
|
#4 |
New Member
Gopal Krishan
Join Date: Aug 2016
Posts: 5
Rep Power: 9 |
Thanks urosgrivc.
I am saving monitor points also. But, I want to save the different phases 0,15,30,.....360 degrees over few cycles according to time so that I can get phase averaged results. And you mentioned about changing the properties of arithmetic average in solver manager, how to do that. Could you please tell me? |
|
November 29, 2017, 15:16 |
|
#5 |
New Member
Gopal Krishan
Join Date: Aug 2016
Posts: 5
Rep Power: 9 |
Thanx Opaque,
I am also getting unexpected results as you mentioned. I have saved different phases according to timesteps or shall I use actual time in start and stop iteration list while setting up the transient statistics? Is there any way to save arithmetic-average results over a cycle at different phase angles? Your kind help will be highly appreciated. |
|
November 30, 2017, 01:55 |
|
#6 |
Senior Member
urosgrivc
Join Date: Dec 2015
Location: Slovenija
Posts: 365
Rep Power: 11 |
Something like this
You can set arithmetic average in solver manager without even chosing it in pre. you can make seperate monitors vith diferent averaging for your monitor points asweal so you can have multiple intervals of averaging etc.. first you right clic on the chart than multiple options are posible; https://drive.google.com/open?id=1cI...D8XFDaxKobjKyn As mentioned there is also an option to export this charts in to the text file Last edited by urosgrivc; December 1, 2017 at 02:13. |
|
November 30, 2017, 22:44 |
|
#7 |
New Member
Gopal Krishan
Join Date: Aug 2016
Posts: 5
Rep Power: 9 |
Thanks, urosgrivc...................
I have to check whether it is solving my problem or not. |
|
December 11, 2017, 21:45 |
|
#8 |
New Member
Gopal Krishan
Join Date: Aug 2016
Posts: 5
Rep Power: 9 |
Hello,
Is there anyone, who can solve this problem??????????? |
|
Tags |
phase-averaging in cfx |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Time average results in Transient CFX Simulation | BalanceChen | CFX | 32 | September 30, 2021 13:59 |
CFX: How to save variables of boundary domain of transient run and use it as input | papanef | CFX | 5 | November 10, 2010 16:31 |
export transient CFX results to tecplot | n.r. | CFX | 0 | October 26, 2007 06:46 |
time averaged results as initial conditions in CFX | mike | CFX | 8 | May 7, 2007 14:54 |
CFX cylinder or sphere benchmark results | Mel | CFX | 1 | August 8, 2005 18:47 |