Information propagation in a subsonic compressor

Julian121 · May 1, 2019, 16:34

Could someone please explain about the information propagating in a subsonic compressor?

As seen in the image, I have put numerical probes in the IGV, Rotor, Stator and casing treatment.

My question is that since information in a subsonic flow regime propagates in upstream direction, should the passing frequencies of the rotor, the stator and the casing treatment or their harmonics appear in the probe I placed in the IGV?

How about the casing treatment?

ghorrocks · May 1, 2019, 19:56

I would imagine so. But whether those frequencies are strong and significant enough to be seen between all the other noise is another matter.

Julian121 · May 2, 2019, 02:57

How about the casing treatment?

Can the the passing frequency of IGV appear in the probe I placed in the casing treatment?

Does it mean that every component in a subsonic compressor feel the presence of other components regardless of their positions?

ghorrocks · May 2, 2019, 03:41

Theoretically, yes. But again, whether the signal from far away features is swamped by noise from other closer features is another matter.

Julian121 · May 17, 2019, 12:19

Which one of instanteous or averaged data should be used to capture blade passing frequency?

I have used a probe which recordrs absoulte pressure.

When I analyse the FFT of this probe, I get half or less than the half of the blade passing frequency.

Why does this happen?

May 1, 2019, 19:56		#2
ghorrocks Super Moderator Glenn Horrocks Join Date: Mar 2009 Location: Sydney, Australia Posts: 18,001 Rep Power: 146	I would imagine so. But whether those frequencies are strong and significant enough to be seen between all the other noise is another matter. __________________ Note: I do not answer CFD questions by PM. CFD questions should be posted on the forum.

May 2, 2019, 03:41		#4
ghorrocks Super Moderator Glenn Horrocks Join Date: Mar 2009 Location: Sydney, Australia Posts: 18,001 Rep Power: 146	Theoretically, yes. But again, whether the signal from far away features is swamped by noise from other closer features is another matter. Julian121 likes this. __________________ Note: I do not answer CFD questions by PM. CFD questions should be posted on the forum.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[TurboGrid] Turbocharger Compressor Wheel Meshing	aymen_a22	ANSYS Meshing & Geometry	0	March 20, 2013 11:27
Compressor Blade Analysis in Ansys CFX	LynchMobster47	Main CFD Forum	0	April 10, 2012 23:43
Terrible Mistake In Fluid Dynamics History	Abhi	Main CFD Forum	12	July 8, 2002 10:11
Inviscid Drag at subsonic, subcritical Mach #	Axel Rohde	Main CFD Forum	1	November 19, 2001 13:19
CFD Problem: volumetric compressor	Gabriele Velenich	Main CFD Forum	2	July 2, 2001 09:15

May 2, 2019, 02:57		#3
Julian121 Senior Member Join Date: Aug 2012 Posts: 269 Rep Power: 16	How about the casing treatment? Can the the passing frequency of IGV appear in the probe I placed in the casing treatment? Does it mean that every component in a subsonic compressor feel the presence of other components regardless of their positions?

May 17, 2019, 12:19		#5
Julian121 Senior Member Join Date: Aug 2012 Posts: 269 Rep Power: 16	Which one of instanteous or averaged data should be used to capture blade passing frequency? I have used a probe which recordrs absoulte pressure. When I analyse the FFT of this probe, I get half or less than the half of the blade passing frequency. Why does this happen?