 |
 |
 |
|
|
|
[Sponsors] | ||||
December 19, 2006, 14:46
|
Workbench on Linux Segmentation Fault
|
#1 |
|
Guest
Posts: n/a
|
I'm attempting to run ANSYS Workbench and/or Design Modeler 10.0 using
gcc version 4.1.0...... Linux version 2.6.16.21-0.25-default (SuSE 10.1) Unfortunately, I keep getting a Segmentation Fault whenever I try and start these programs. CFX10.0 works, but these do not. Has anyone ever had these problems or can suggest anyway of fixing them? |
|
|
||
|
December 20, 2006, 07:11
|
Re: Workbench on Linux Segmentation Fault
|
#2 |
|
Guest
Posts: n/a
|
AFAIK workbench isnt supported on linux? (Or is it just not supported on X86 linux???)
Have a look at the workbench install guide ... |
|
|
|
||
|
December 27, 2006, 05:16
|
CFX 10 and EM64T, is it possible?
|
#3 |
|
Guest
Posts: n/a
|
Question, are you using the CFX 10 for Linux AMD 64 install? I am asking because I am looking to run version 10 on and quad core Intel using SuSE, but am not sure if there is a version for linux that runs on the EM64T ? I need 64 bit for the memory requirements, any help would be good. Thanks Tony F
|
|
|
|
||
|
December 27, 2006, 14:16
|
Re: CFX 10 and EM64T, is it possible?
|
#4 |
|
Guest
Posts: n/a
|
AMD x64 executables should run fine on an Intel EMT64 AFAIK.
|
|
|
|
||
|
December 27, 2006, 17:22
|
Re: CFX 10 and EM64T, is it possible?
|
#5 |
|
Guest
Posts: n/a
|
Excellent, thanks Tony
|
|
|
|
||
|
January 3, 2007, 00:05
|
Re: CFX 10 and EM64T, is it possible?
|
#6 |
|
Guest
Posts: n/a
|
It runs but you need a minor, unofficial, patch to cfx 10. Contact your support rep.
|
|
|
|
||
|
January 3, 2007, 13:45
|
Re: CFX 10 and EM64T, is it possible?
|
#7 |
|
Guest
Posts: n/a
|
EM64T is supported natively in CFX 11 I presume?
I ask because we are switching from Opterons to Xeons soon ... |
|
|
|
||
 |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| ANSYS Workbench on "Uncertified" Linux Distros | hsr | CFX | 289 | April 20, 2023 09:23 |
| Segmentation fault when running dieselFoam or dieselEngineFoam in parallel | francesco | OpenFOAM Bugs | 4 | May 2, 2017 21:59 |
| LINUX Experts: Help with installing ANSYS workbench | faisal_durr | ANSYS | 1 | May 30, 2014 08:07 |
| Workbench 11-Linux Intel EM64T platforms Seg fault | Maciej Karczewski | CFX | 5 | April 19, 2010 03:37 |
| ParaView segmentation fault only for multiphase | gwierink | OpenFOAM | 9 | March 25, 2010 07:23 |
Linear Mode
