CFX results postprocess in Tecplot

seaharrier · June 26, 2009, 03:16

hi, everyone,
I simulate rotor 37 in CFX, but want to postprocess the result in Tecplot, i don't know how to cut a B2B surface because the CFX mesh is considered as unstructural.

Could somebody help me?

Thanks very much.

ghorrocks · June 26, 2009, 07:14

Hi,

I think there is a tecplot export option. Go to the solver manager, under tools I think there is an export data gizmo. I don't have CFX in front of me so can't give you the exact location.

Glenn Horrocks

seaharrier · June 26, 2009, 22:12

thanks Glenn，

i did the export of CGNS format, but there's no such an option as exporting a result basing on structural grid. the problem is in CFX itself, solving equationgs of conservation in unstructured grid.

could i make some change by a coding or other methods, anyway,
only to extract some surface like B2B in Tecplot?

perhaps i must seek help in Tecplot helping PDFs.

ghorrocks · June 27, 2009, 06:27

Hi,

Well then you are stuck because CFX is an unstructured solver so there is no way it will output a structured grid. If your grid is actually structured you could write your own export routine then you would get a structured grid output. Have a look in the documentation for how to do this.

But my guess is you will be unlikely to do better than the existing CGNS export so why not stick with that.

I don't know what you mean by extracting surfaces. Do you want the full 3D domain or just the boundaries? What are you trying to do with the output anyway?

Glenn Horrocks

seaharrier · June 27, 2009, 07:35

Thank you very much,Glenn,
I just want to make some turbo surfaces in Tecplot, such as that in CFX post turbo module.
Thanks for your advice, I will try doing that in Tecplot,
maybe this is the easiest practice.

qinglonger · April 18, 2019, 01:01

Hi,
I simulated a centrifugal compressor in NUMECA and imported the CGNS format flie into
Tecplot. Now, I want to cut a B2B surface, such as that in CFVIEW or CFX post.
Have you solved this problem in Tecplot?
Thank you!

June 26, 2009, 03:16	CFX results postprocess in Tecplot	#1
seaharrier New Member Join Date: Jun 2009 Posts: 11 Rep Power: 16	hi, everyone, I simulate rotor 37 in CFX, but want to postprocess the result in Tecplot, i don't know how to cut a B2B surface because the CFX mesh is considered as unstructural. Could somebody help me? Thanks very much.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
comparison with analytical results (1D)and(3D) CFX	Rogerio Fernandes Brito	FLUENT	1	December 2, 2012 06:12
Reading CFX-CFD results without Ansys CFX	JAY	ANSYS	2	July 7, 2009 16:48
CFX - Tecplot	Ilona	CFX	1	September 2, 2004 00:20
CFX 5.5.1 and writing intermediate results	Andrej	CFX	1	January 18, 2003 21:00
CFX post to Tecplot	nandu	CFX	2	December 4, 2002 08:27

June 26, 2009, 07:14		#2
ghorrocks Super Moderator Glenn Horrocks Join Date: Mar 2009 Location: Sydney, Australia Posts: 17,703 Rep Power: 143	Hi, I think there is a tecplot export option. Go to the solver manager, under tools I think there is an export data gizmo. I don't have CFX in front of me so can't give you the exact location. Glenn Horrocks

June 26, 2009, 22:12		#3
seaharrier New Member Join Date: Jun 2009 Posts: 11 Rep Power: 16	thanks Glenn， i did the export of CGNS format, but there's no such an option as exporting a result basing on structural grid. the problem is in CFX itself, solving equationgs of conservation in unstructured grid. could i make some change by a coding or other methods, anyway, only to extract some surface like B2B in Tecplot? perhaps i must seek help in Tecplot helping PDFs.

June 27, 2009, 06:27		#4
ghorrocks Super Moderator Glenn Horrocks Join Date: Mar 2009 Location: Sydney, Australia Posts: 17,703 Rep Power: 143	Hi, Well then you are stuck because CFX is an unstructured solver so there is no way it will output a structured grid. If your grid is actually structured you could write your own export routine then you would get a structured grid output. Have a look in the documentation for how to do this. But my guess is you will be unlikely to do better than the existing CGNS export so why not stick with that. I don't know what you mean by extracting surfaces. Do you want the full 3D domain or just the boundaries? What are you trying to do with the output anyway? Glenn Horrocks

June 27, 2009, 07:35		#5
seaharrier New Member Join Date: Jun 2009 Posts: 11 Rep Power: 16	Thank you very much,Glenn, I just want to make some turbo surfaces in Tecplot, such as that in CFX post turbo module. Thanks for your advice, I will try doing that in Tecplot, maybe this is the easiest practice.

April 18, 2019, 01:01		#6
qinglonger New Member Join Date: Jan 2017 Posts: 2 Rep Power: 0	Hi, I simulated a centrifugal compressor in NUMECA and imported the CGNS format flie into Tecplot. Now, I want to cut a B2B surface, such as that in CFVIEW or CFX post. Have you solved this problem in Tecplot? Thank you!