Split Monitor for Residuals

uwsa · August 26, 2010, 09:30

Hi @all,

maybe it is a simple question but I could not find a solution for it.
1. Is there a possibility to seperate the output control for different variables? e.g. one monitor for temperatures and another one for massflow but not both in one!

2. Is there a possiblity in cfx-post to express the values for a couple of points altogether? I know how to plot the value for a plane or a line or a single point and then to express them out. However how it is working for a 300 Points?

Thanks a lot for every help.

Best wishes
uwsa

stumpy · August 26, 2010, 17:10

1. Sure. Just right-click on your monitor when the solver is running and select which lines you want to display. Create a new monitor (in the Solver Manager) to display the other one.

2. You just need a loop. Search the doc for "Power Syntax Example 2 Using a for Loop". You would just write that loop into the Command Editor in CFD-Post.

bharath · August 26, 2010, 23:12

alternatively you can use table to get the values
(probe(velocity)@point 1,2,3....)

uwsa · September 14, 2010, 04:42

great thank you to all. Both options are well.

Sometimes life can be so easiy with a little help

Thank you again.

August 26, 2010, 09:30	Split Monitor for Residuals	#1
uwsa New Member Erkan Join Date: May 2010 Posts: 9 Rep Power: 17	Hi @all, maybe it is a simple question but I could not find a solution for it. 1. Is there a possibility to seperate the output control for different variables? e.g. one monitor for temperatures and another one for massflow but not both in one! 2. Is there a possiblity in cfx-post to express the values for a couple of points altogether? I know how to plot the value for a plane or a line or a single point and then to express them out. However how it is working for a 300 Points? Thanks a lot for every help. Best wishes uwsa

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[GAMBIT] Split volume - when reflecting volume, the copy blows up	enfinity	ANSYS Meshing & Geometry	7	May 3, 2011 03:13
[ICEM] Split O grid	BrolY	ANSYS Meshing & Geometry	1	July 2, 2010 10:23
how to split hex mesh in icem with desired height?	adam2008	ANSYS Meshing & Geometry	3	August 27, 2009 15:59
split functioin in CCM+	Peter Specht	Siemens	1	March 5, 2008 09:14
fluent add additional zones for the mesh file	SSL	FLUENT	2	January 26, 2008 12:55

August 26, 2010, 17:10		#2
stumpy Senior Member Join Date: Apr 2009 Posts: 531 Rep Power: 22	1. Sure. Just right-click on your monitor when the solver is running and select which lines you want to display. Create a new monitor (in the Solver Manager) to display the other one. 2. You just need a loop. Search the doc for "Power Syntax Example 2 Using a for Loop". You would just write that loop into the Command Editor in CFD-Post.

August 26, 2010, 23:12		#3
bharath Senior Member Bharath kumar Join Date: Apr 2009 Posts: 169 Rep Power: 18	alternatively you can use table to get the values (probe(velocity)@point 1,2,3....)

September 14, 2010, 04:42		#4
uwsa New Member Erkan Join Date: May 2010 Posts: 9 Rep Power: 17	great thank you to all. Both options are well. Sometimes life can be so easiy with a little help Thank you again.