Subsonic and Transonic Flow

zacko · March 3, 2018, 09:20

Hello there,

I am simulating a 4-stage axial compressor with subsonic flow.
When I evaluated the mach-number at the inlet of the first rotor row, the Mach-number near the Shroud reached 0.85.
For me this is a little but curious since I defined the flow with subsonic.
Is it normal, that the Flow exceeds 0.8 for transonic flow conditions?

Thank you very much!

Far · March 3, 2018, 10:49

yes very much normal

zacko · March 3, 2018, 12:58

Thanks for the answer

But is there any explanation for this ?

Far · March 3, 2018, 13:01

isnt is the velocity triangle. at tip the blade speed is higher, so the mach number

Far · March 3, 2018, 13:02

you have to check it is relative mach number or mach number.

zacko · March 3, 2018, 13:04

I only can choose Mach Number and Mach Number in Stn Frame.
And for the Rotor I've chosen the regular Mach Number.

Far · March 3, 2018, 13:55

it is relative mach number

March 3, 2018, 09:20	Subsonic and Transonic Flow	#1
zacko Senior Member Daniel Join Date: Feb 2017 Location: Germany Posts: 147 Rep Power: 9	Hello there, I am simulating a 4-stage axial compressor with subsonic flow. When I evaluated the mach-number at the inlet of the first rotor row, the Mach-number near the Shroud reached 0.85. For me this is a little but curious since I defined the flow with subsonic. Is it normal, that the Flow exceeds 0.8 for transonic flow conditions? Thank you very much!

March 3, 2018, 10:49		#2
Far Super Moderator Sijal Join Date: Mar 2009 Location: Islamabad Posts: 4,553 Blog Entries: 6 Rep Power: 54	yes very much normal zacko likes this.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Issues on the simulation of high-speed compressible flow within turbomachinery	dowlee	OpenFOAM Running, Solving & CFD	11	August 6, 2021 06:40
Boundary conditions for flow in nozzle	kgevers	FLUENT	0	July 26, 2015 12:46
Subsonic or transonic flow over a bump in a channel.	AshwaniAssam	Main CFD Forum	2	January 8, 2014 00:35
heat transfer probs by transonic flow	Josh_Blue	FLUENT	8	March 21, 2010 05:31
Inviscid Drag at subsonic, subcritical Mach #	Axel Rohde	Main CFD Forum	1	November 19, 2001 12:19

March 3, 2018, 12:58		#3
zacko Senior Member Daniel Join Date: Feb 2017 Location: Germany Posts: 147 Rep Power: 9	Thanks for the answer But is there any explanation for this ?

March 3, 2018, 13:01		#4
Far Super Moderator Sijal Join Date: Mar 2009 Location: Islamabad Posts: 4,553 Blog Entries: 6 Rep Power: 54	isnt is the velocity triangle. at tip the blade speed is higher, so the mach number

March 3, 2018, 13:02		#5
Far Super Moderator Sijal Join Date: Mar 2009 Location: Islamabad Posts: 4,553 Blog Entries: 6 Rep Power: 54	you have to check it is relative mach number or mach number.

March 3, 2018, 13:04		#6
zacko Senior Member Daniel Join Date: Feb 2017 Location: Germany Posts: 147 Rep Power: 9	I only can choose Mach Number and Mach Number in Stn Frame. And for the Rotor I've chosen the regular Mach Number.

March 3, 2018, 13:55		#7
Far Super Moderator Sijal Join Date: Mar 2009 Location: Islamabad Posts: 4,553 Blog Entries: 6 Rep Power: 54	it is relative mach number