Error Code in Vented Brake Rotor

neilth · May 14, 2011, 03:06

I am modeling the air flow through the passages of a vented brake disc. The model is cut down to a 5 degree section that represents one passage. No matter what I try i.e. stationary vs rotational when the transient solver run is complete I get this error:

The ANSYS CFX solver has terminated without writing a results file.
Command on host ws3148629 (WS314-86-29) exited with return code 0.

What does this mean?

ghorrocks · May 14, 2011, 06:12

A bit of context would help.

Has the run completed and it given the error at the end? Or did it not even get started?

neilth · May 15, 2011, 03:05

Yes, the run has completed for each attempt before this error is given at the end of each run.

ghorrocks · May 15, 2011, 18:59

Did the network go down? Is the hard drive full? Do you have write access?

saileshk14 · May 17, 2011, 06:03

Hello ! Im facing a similar problem, actually the same. Anybody have a solution to this. Does this happen if the meshing is improper?

Shabridev · October 9, 2018, 05:24

I m running CFX analysis on the rotor designed by me,
From scratch, I have designed a rotor, I made a rectangular hollow box which is enclosing the rotor. Then I imported the part from solidworks and then I did named selection in which 2 faces of the box were inlet and outlet and rest faces be the wall, and the rotor is also made a selection. Meshing was done and now in CFX-PRE I declared the boundary conditions to the named selection and then I did the global intialization in which the velocity type was kept Cartesian and Cartesian components automatic.
When i run the solver, it returns an error which states *update failed for solution components in fluid flow,the solver failed with a non-zero exit code
I am not getting any output.
Please help me as soon as possible.

Regards,
Spark Racing Team

ghorrocks · October 10, 2018, 18:28

The error messages in workbench are not useful. Open the output file and look in there as that is where the useful error messages are displayed.

May 14, 2011, 03:06	Error Code in Vented Brake Rotor	#1
neilth New Member Neil Heilemann Join Date: Apr 2011 Posts: 6 Rep Power: 14	I am modeling the air flow through the passages of a vented brake disc. The model is cut down to a 5 degree section that represents one passage. No matter what I try i.e. stationary vs rotational when the transient solver run is complete I get this error: The ANSYS CFX solver has terminated without writing a results file. Command on host ws3148629 (WS314-86-29) exited with return code 0. What does this mean?

May 15, 2011, 03:05		#3
neilth New Member Neil Heilemann Join Date: Apr 2011 Posts: 6 Rep Power: 14	Yes, the run has completed for each attempt before this error is given at the end of each run. Last edited by neilth; May 15, 2011 at 03:37.

October 10, 2018, 18:28		#7
ghorrocks Super Moderator Glenn Horrocks Join Date: Mar 2009 Location: Sydney, Australia Posts: 17,700 Rep Power: 143	The error messages in workbench are not useful. Open the output file and look in there as that is where the useful error messages are displayed. __________________ Note: I do not answer CFD questions by PM. CFD questions should be posted on the forum.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
CFD analysis on wind turbine rotor	Ken (Wind Turbine CFD Super Rookie)	Main CFD Forum	45	February 9, 2016 14:07
Vented Brake Rotor	neilth	CFX	2	May 9, 2011 00:04
Bike brake rotor simulation	gnuboard	CFX	3	August 2, 2010 19:02
rotor brake	mAx	FLUENT	0	September 13, 2006 01:47
Brake Rotor Thermal Calculation in STAR-CD- Urgent	ps	Siemens	3	June 27, 2006 04:18

May 14, 2011, 06:12		#2
ghorrocks Super Moderator Glenn Horrocks Join Date: Mar 2009 Location: Sydney, Australia Posts: 17,700 Rep Power: 143	A bit of context would help. Has the run completed and it given the error at the end? Or did it not even get started?

May 15, 2011, 18:59		#4
ghorrocks Super Moderator Glenn Horrocks Join Date: Mar 2009 Location: Sydney, Australia Posts: 17,700 Rep Power: 143	Did the network go down? Is the hard drive full? Do you have write access?

May 17, 2011, 06:03		#5
saileshk14 New Member Sailesh K Join Date: May 2011 Posts: 1 Rep Power: 0	Hello ! Im facing a similar problem, actually the same. Anybody have a solution to this. Does this happen if the meshing is improper?

October 9, 2018, 05:24		#6
Shabridev New Member Join Date: Oct 2018 Posts: 1 Rep Power: 0	I m running CFX analysis on the rotor designed by me, From scratch, I have designed a rotor, I made a rectangular hollow box which is enclosing the rotor. Then I imported the part from solidworks and then I did named selection in which 2 faces of the box were inlet and outlet and rest faces be the wall, and the rotor is also made a selection. Meshing was done and now in CFX-PRE I declared the boundary conditions to the named selection and then I did the global intialization in which the velocity type was kept Cartesian and Cartesian components automatic. When i run the solver, it returns an error which states *update failed for solution components in fluid flow,the solver failed with a non-zero exit code I am not getting any output. Please help me as soon as possible. Regards, Spark Racing Team