Inlet and Outlet in the same boundary

foo7 · August 22, 2011, 08:00

Hello.

I've been working with finite elements simulation for a while now, but I'm new to CFX.

Recently I've been trying to simulate the following process:

Geometry: Cylindrical column
Fluids: Hot air and solid
Situation: The column has a lateral opening where hot air is blown, an open top from where solid is introduced and hot gas is collected and an open bottom from where solid is collected.
The objective is to react the solid with the hot air and collect the resulting gas from the top and the reacted solids from the bottom.

My problem lies with some of the boundary conditions for each of these openings.

1 - For the lateral opening, no problem, I just have to set it as an inlet and set the normal speed of the air injection and the volume fraction of air equal to 1 and the solid's equal to zero.

2 - For the bottom opening, no problem also, as I only have to set it as an outlet and set the mass outflow rate for the solids.

3 - But for the top opening, I don't know what to do. I have to conditions to impose: the solid's inflow rate and the gases' outflow rate. How can I do this? Is there a way to set this boundary as an inlet for the gas and a outlet for the solids???

Thanks very much for your help.

Have a nice day!

swiss_zhang · August 22, 2011, 10:43

Can you post your geometry?

foo7 · August 22, 2011, 11:43

hosting images
Here it is.
The lateral inlet is clear in the picture.
The bottom outlet is located right under the lateral inlet.
And the problematic boundary is the one on the top. In which I wanna apply a outlet boundary condition for the gas phase and a inlet boundary condition for the solids.

August 22, 2011, 08:00	Inlet and Outlet in the same boundary	#1
foo7 Disabled Join Date: Aug 2011 Posts: 10 Rep Power: 14	Hello. I've been working with finite elements simulation for a while now, but I'm new to CFX. Recently I've been trying to simulate the following process: Geometry: Cylindrical column Fluids: Hot air and solid Situation: The column has a lateral opening where hot air is blown, an open top from where solid is introduced and hot gas is collected and an open bottom from where solid is collected. The objective is to react the solid with the hot air and collect the resulting gas from the top and the reacted solids from the bottom. My problem lies with some of the boundary conditions for each of these openings. 1 - For the lateral opening, no problem, I just have to set it as an inlet and set the normal speed of the air injection and the volume fraction of air equal to 1 and the solid's equal to zero. 2 - For the bottom opening, no problem also, as I only have to set it as an outlet and set the mass outflow rate for the solids. 3 - But for the top opening, I don't know what to do. I have to conditions to impose: the solid's inflow rate and the gases' outflow rate. How can I do this? Is there a way to set this boundary as an inlet for the gas and a outlet for the solids??? Thanks very much for your help. Have a nice day!

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Wind turbine simulation	Saturn	CFX	58	July 3, 2020 01:13
RPM in Wind Turbine	Pankaj	CFX	9	November 23, 2009 04:05
Convective Heat Transfer - Heat Exchanger	Mark	CFX	6	November 15, 2004 15:55
New topic on same subject - Flow around race car	Tudor Miron	CFX	15	April 2, 2004 06:18
Please help with flow around car modelling!	Tudor Miron	CFX	17	March 19, 2004 19:23

August 22, 2011, 10:43		#2
swiss_zhang New Member Zhang Yang Join Date: Jun 2011 Location: Zürich Posts: 28 Rep Power: 15	Can you post your geometry?

August 22, 2011, 11:43		#3
foo7 Disabled Join Date: Aug 2011 Posts: 10 Rep Power: 14	hosting images Here it is. The lateral inlet is clear in the picture. The bottom outlet is located right under the lateral inlet. And the problematic boundary is the one on the top. In which I wanna apply a outlet boundary condition for the gas phase and a inlet boundary condition for the solids.