FFT for Post Simulation Analysis

faisal_durr · May 31, 2011, 04:59

Hello Guys, Im looking at using LES to look at plumes in a naturally ventilated building. I have set up statistical results for the velocity, temperature and pressure variables in cfx-pre and run the simulation for which I now have the results. I need to now run an FFT analysis on the simulation results I have got. I do have matlab to help out with the FFT. But I need the help of you experts out there to tell how to do this. It would be really great if you could tell me in steps how to take things from cfx-post (for example), to matlab and then run the FFT. Thank you so very much

ojha.mayank485 · May 31, 2011, 16:20

I ran a FFT using MATLAB to find the frequency of vortex shedding for a flow over a bluff body. This is what I did.

Once you get your values of your data wrt time, export everything to EXCEL and make MATLAB read the EXCEL file to get the FFT graph of Power spectrum vs Freq.

You can use the readxlsx command in MATLAB to read all your data values. Matlab will read all the data values from the EXCEL file into an ARRAY and then use the FFT function in MATLAB to calculate the Frequency.

Hope this helped.

faisal_durr · June 7, 2011, 07:03

Quote:

Originally Posted by ojha.mayank485

I ran a FFT using MATLAB to find the frequency of vortex shedding for a flow over a bluff body. This is what I did.

Once you get your values of your data wrt time, export everything to EXCEL and make MATLAB read the EXCEL file to get the FFT graph of Power spectrum vs Freq.

You can use the readxlsx command in MATLAB to read all your data values. Matlab will read all the data values from the EXCEL file into an ARRAY and then use the FFT function in MATLAB to calculate the Frequency.

Hope this helped.

Hey buddy thanks for the reply. I am also looking at vortex shedding myself. I would love to see your work if its published or your theses if you have written one. I have some questions I would like you to answer please. I am thinking of plotting velocity vs. time to get the graph. This will be done at a specific point right with the help of monitors right? And one i plot this as a chart in post then I will export the chart to excel, am I correct? Thanks for the help

ojha.mayank485 · June 7, 2011, 17:57

Quote:

Originally Posted by faisal_durr

Hey buddy thanks for the reply. I am also looking at vortex shedding myself. I would love to see your work if its published or your theses if you have written one. I have some questions I would like you to answer please. I am thinking of plotting velocity vs. time to get the graph. This will be done at a specific point right with the help of monitors right? And one i plot this as a chart in post then I will export the chart to excel, am I correct? Thanks for the help

Quote:

I would love to see your work if its published or your theses if you have written one

I do not have anything published results yet. I have a few stuff remaining to do.

Quote:

I am thinking of plotting velocity vs. time to get the graph. This will be done at a specific point right with the help of monitors right? And one i plot this as a chart in post then I will export the chart to excel, am I correct?

For me I plotted the forces over the surface but you can certainly do it for a point. YES !!!! Then right click on the plot and export it to EXCEL.

Then write a Matlab script to read values from the EXCEL file that has been created and use the FFT function to get your frequency.

Let me know if you need any more help.

omidiut · June 8, 2011, 07:11

Hi. ojha.mayank485
How do you use FFT in MATLAB? can you explain the syntax of this function that you use it?
I do it by Freqz function in MATLAB but my result is not reasonable.

Best regards

omidiut · June 8, 2011, 07:13

Quote:

Originally Posted by ojha.mayank485

I do not have anything published results yet. I have a few stuff remaining to do.

For me I plotted the forces over the surface but you can certainly do it for a point. YES !!!! Then right click on the plot and export it to EXCEL.

Then write a Matlab script to read values from the EXCEL file that has been created and use the FFT function to get your frequency.

Let me know if you need any more help.

Hi. ojha.mayank485
How do you use FFT in MATLAB? can you explain the syntax of this function that you use it?
I do it by Freqz function in MATLAB but my result is not reasonable.

Best regards

ojha.mayank485 · June 8, 2011, 12:22

Send me an email at ojha.mayank485@gmail.com and I'll send you the MATLAB script and the xlsx file containing the Cl over my bluff body. It is a small code.
Just looking at the MATLAB syntax will give you a clear idea of what is happening.

I have not heard of the freq function. You should be using the FFT in-build function.

omidiut · June 8, 2011, 15:11

Thanks for reply Mayank Ojha
Best regards

zoozoozoo · August 5, 2011, 19:37

Hey Mayank,

I'm interested in exactly the same issue. Do you think it would be possible to have a look at your Matlab script, as well. Would be great and appreciated.

thanks inn advance.
matt

famerfamer · September 3, 2011, 16:59

Quote:

Originally Posted by omidiut

Hi. ojha.mayank485
How do you use FFT in MATLAB? can you explain the syntax of this function that you use it?
I do it by Freqz function in MATLAB but my result is not reasonable.

Best regards

Hey,

Could you also send me your matlab script? I'm working on the same thing right now. Thanks! tamubruce at gmail.com

Sal · September 5, 2011, 06:38

Just to remind you guys that in the CFD-Post you can insert a new Chart XY - Transient or Sequence read data from any monitor point control, file (.csv that you can also export from CFX-Solver Manager Monitor) or time-dependent expression. Then enable Fast Fourier Transform (FFT) and off you go. This is very handy.
Good luck.

rujia · September 14, 2011, 06:07

hello everyone:
there are 3 component for velocity field in my results. In matlab, which velocity is used for getting the energy spectrum. maybe, the turbulence kinetic energy should be calculated for the spectrum, isn't it?

Sonik_87 · March 13, 2012, 03:35

Hello guys, I am at the moment writing a code for solving the fluid motion about a 2D airfoil via a Linear-Strength-Vortex Method. I am at the point in which I need to validate my unsteady code and therefore I would like to compare my results with some NACA papers in which the coefficients of the Fourier series are plotted. For example:

Cp= Cp0+Cp1s*sin(wt)+Cp1c*cos(wt)+Cp2*sin(2wt+phi)

My problem is I don't really understand how to obtain these coefficients from the fft function. What I have is the value of Cp on each panel at each time step: so let's say we have 60 panels and 100 time steps, I have a Cp matrix of Cp(60,100). Applying the fft to this I get again a 60x100 matrix (with complex numbers). I do not know how to use this data. I somewhere found a guid which says the coefficients (a0, a1, b1, a2, b2, ...) are to be calculated via division by N/2... but I still don't understand.
Could you help me letting some light in the matter?

Thank you very much.
A.

May 31, 2011, 04:59	FFT for Post Simulation Analysis	#1
faisal_durr Member Faisal Durrani Join Date: Nov 2009 Location: England Posts: 62 Rep Power: 16	Hello Guys, Im looking at using LES to look at plumes in a naturally ventilated building. I have set up statistical results for the velocity, temperature and pressure variables in cfx-pre and run the simulation for which I now have the results. I need to now run an FFT analysis on the simulation results I have got. I do have matlab to help out with the FFT. But I need the help of you experts out there to tell how to do this. It would be really great if you could tell me in steps how to take things from cfx-post (for example), to matlab and then run the FFT. Thank you so very much

May 31, 2011, 16:20	@ faisal	#2
ojha.mayank485 New Member Mayank Ojha Join Date: May 2011 Posts: 22 Rep Power: 14	I ran a FFT using MATLAB to find the frequency of vortex shedding for a flow over a bluff body. This is what I did. Once you get your values of your data wrt time, export everything to EXCEL and make MATLAB read the EXCEL file to get the FFT graph of Power spectrum vs Freq. You can use the readxlsx command in MATLAB to read all your data values. Matlab will read all the data values from the EXCEL file into an ARRAY and then use the FFT function in MATLAB to calculate the Frequency. Hope this helped. openfoam_aero likes this.

June 8, 2011, 12:22		#7
ojha.mayank485 New Member Mayank Ojha Join Date: May 2011 Posts: 22 Rep Power: 14	Send me an email at ojha.mayank485@gmail.com and I'll send you the MATLAB script and the xlsx file containing the Cl over my bluff body. It is a small code. Just looking at the MATLAB syntax will give you a clear idea of what is happening. I have not heard of the freq function. You should be using the FFT in-build function. Subrahmanyam likes this.

March 13, 2012, 03:35	fft in Matlab	#13
Sonik_87 New Member Anthony Join Date: Jul 2011 Posts: 9 Rep Power: 14	Hello guys, I am at the moment writing a code for solving the fluid motion about a 2D airfoil via a Linear-Strength-Vortex Method. I am at the point in which I need to validate my unsteady code and therefore I would like to compare my results with some NACA papers in which the coefficients of the Fourier series are plotted. For example: Cp= Cp0+Cp1ssin(wt)+Cp1ccos(wt)+Cp2*sin(2wt+phi) My problem is I don't really understand how to obtain these coefficients from the fft function. What I have is the value of Cp on each panel at each time step: so let's say we have 60 panels and 100 time steps, I have a Cp matrix of Cp(60,100). Applying the fft to this I get again a 60x100 matrix (with complex numbers). I do not know how to use this data. I somewhere found a guid which says the coefficients (a0, a1, b1, a2, b2, ...) are to be calculated via division by N/2... but I still don't understand. Could you help me letting some light in the matter? Thank you very much. A.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Fluid structure interaction	jnattia	Main CFD Forum	25	May 21, 2015 09:16
1d analysis and simulation of gas turbine power plant	sridhar.d009	FLUENT	0	September 28, 2010 07:46
1D analysis and simulation of gas turbine power plant	sridhar.d009	Main CFD Forum	1	September 28, 2010 07:38
velocity profile export from a simulation onto another	sudhirlv	STAR-CCM+	1	September 12, 2010 18:57
3-D Contaminant Dispersal Simulation	Apple L S Chan	Main CFD Forum	1	December 23, 1998 10:06

June 8, 2011, 07:11		#5
omidiut Senior Member omid Join Date: Apr 2011 Posts: 105 Rep Power: 14	Hi. ojha.mayank485 How do you use FFT in MATLAB? can you explain the syntax of this function that you use it? I do it by Freqz function in MATLAB but my result is not reasonable. Best regards

June 8, 2011, 15:11		#8
omidiut Senior Member omid Join Date: Apr 2011 Posts: 105 Rep Power: 14	Thanks for reply Mayank Ojha Best regards

August 5, 2011, 19:37		#9
zoozoozoo New Member MG Join Date: Aug 2009 Posts: 7 Rep Power: 16	Hey Mayank, I'm interested in exactly the same issue. Do you think it would be possible to have a look at your Matlab script, as well. Would be great and appreciated. thanks inn advance. matt

September 5, 2011, 06:38		#11
Sal New Member Join Date: Jun 2011 Posts: 15 Rep Power: 14	Just to remind you guys that in the CFD-Post you can insert a new Chart XY - Transient or Sequence read data from any monitor point control, file (.csv that you can also export from CFX-Solver Manager Monitor) or time-dependent expression. Then enable Fast Fourier Transform (FFT) and off you go. This is very handy. Good luck.

September 14, 2011, 06:07		#12
rujia New Member ya Join Date: Apr 2011 Posts: 7 Rep Power: 15	hello everyone: there are 3 component for velocity field in my results. In matlab, which velocity is used for getting the energy spectrum. maybe, the turbulence kinetic energy should be calculated for the spectrum, isn't it?