|
[Sponsors] |
An error when Converge reads embedded.in data |
|
LinkBack | Thread Tools | Search this Thread | Display Modes |
November 27, 2016, 09:09 |
An error when Converge reads embedded.in data
|
#1 |
New Member
Jietuo
Join Date: Jul 2016
Posts: 25
Rep Power: 9 |
I encountered a problem.
When Converge deactivates triangles in a disconnect group, the process stop. And, there is no error message available. So, I searched related information in manual and founded this. "Initialization of Events When starting a simulation, CONVERGE disconnects all adjacent regions and then processes the events up to the start time. If events.in is CYCLIC, CONVERGE will process all events for one full cycle and then up until the simulation start time. This is necessary because, in a CYCLIC case, the initial region connection status depends on the region connection status at the end of the previous cycle." But it cannot help me solve the problem.What should I do to correct the error. |
|
November 28, 2016, 09:04 |
|
#2 |
Senior Member
Tobias
Join Date: May 2016
Location: Germany
Posts: 264
Rep Power: 10 |
What exactly are you trying to simulate?
I have never seen so many rows of activating/deactivating disconnect triangles. Maybe you could post the events.in file? |
|
November 28, 2016, 11:16 |
|
#3 |
New Member
Jing Huang
Join Date: Dec 2015
Location: Convergent Science, Madison WI
Posts: 23
Rep Power: 10 |
Hi, please try the latest solver. If the problem is still there, please send your case file to support@convergecfd.com. Thanks!
|
|
November 28, 2016, 20:23 |
an error occurs when Converge reads files
|
#4 | |
New Member
Jietuo
Join Date: Jul 2016
Posts: 25
Rep Power: 9 |
Quote:
However, after discussing with my workmates, I think the problem may result from the 3-D model. I will modify the model, and try again. Thank you a lot. |
||
November 28, 2016, 20:26 |
|
#5 |
New Member
Jietuo
Join Date: Jul 2016
Posts: 25
Rep Power: 9 |
Yeah. When I use the latest solver, the problem raise again. If I cannot solve it, I will sent my case files to the email address. Thank you for your suggestion.
|
|
November 29, 2016, 11:51 |
|
#6 |
New Member
Jing Huang
Join Date: Dec 2015
Location: Convergent Science, Madison WI
Posts: 23
Rep Power: 10 |
Can you try to run the case in nohydro mode and see if the problem is still there? Just set nohydro in inputs.in to 1.
I am also thinking of changing parallel_scale too. Just give it a try between -1 to -4. Thanks! |
|
November 29, 2016, 12:09 |
|
#7 |
Senior Member
Tobias
Join Date: May 2016
Location: Germany
Posts: 264
Rep Power: 10 |
Are you sure that the events take place before the surface (vavles) are moving?
|
|
November 29, 2016, 20:21 |
|
#8 |
New Member
Jietuo
Join Date: Jul 2016
Posts: 25
Rep Power: 9 |
As you said, I run the case in nohydro mode, and the problem is still there. So, should I check the surface.data?
|
|
November 29, 2016, 20:29 |
|
#9 |
New Member
Jietuo
Join Date: Jul 2016
Posts: 25
Rep Power: 9 |
The model is a model of two stroke marine engine. So there is no intake valve. The air is induced by scavenging process. And, the events in the 3rd and 4th row of the event.in are about two gas fuel injector. I don't know whether I explain my problem clearly. But I found that when I run the case in nohydro mode, just as Jing Huang said, the problem was also there.
|
|
November 30, 2016, 09:45 |
|
#10 |
New Member
Jing Huang
Join Date: Dec 2015
Location: Convergent Science, Madison WI
Posts: 23
Rep Power: 10 |
Ok I see you are using sealing since it's a two stroke engine. In this case we need to specify NO_DIS_Triangles for the combustion chamber region in events.in:
#-------------- NO_DIS_Triangles 1 1 region_id #-------------- where region_id is the combustion chamber region (please refer to CONVERGE Manual 7.2.3). I am not sure this is the cause of the problem though. Two stroke engine case can be tricky, I think the best way is to sending your case to support team for a look. Thanks! |
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
CFD by anderson, chp 10.... supersonic flow over flat plate | varunjain89 | Main CFD Forum | 18 | May 11, 2018 07:31 |
[OpenFOAM] Paraview doesn't seem to be picking up data generated by icofoam | MikeHersee | ParaView | 2 | January 6, 2015 08:27 |
Data Produced From Fine Marine Cant Match with The Experimental Data | PeiSan | Fidelity CFD | 4 | August 23, 2014 05:33 |
Problem running in parralel | Val | OpenFOAM Running, Solving & CFD | 1 | June 12, 2014 02:47 |
Simulated data vs. experimental data | moiami | FLUENT | 0 | December 19, 2002 01:03 |