CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums > Software User Forums > CONVERGE

JOB ABORT invoked by rank 0

Register Blogs Members List Search Today's Posts Mark Forums Read

Like Tree1Likes
  • 1 Post By ksrivast

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old   September 15, 2017, 07:53
Default JOB ABORT invoked by rank 0
  #1
New Member
 
Ankit Raut
Join Date: Sep 2017
Location: Chennai
Posts: 14
Rep Power: 5
ankitraut27 is on a distinguished road
Hello Everyone,

I am getting same error again and again. Error message is as below:
" JOB ABORT invoked by rank 0
ERROR: wrong boundary motion_type in calc_moving_vec boundary id = 16"

What does this error mean? I have only 15 boundaries in my case. Then from where this boundary id 16 came?

Please Help!

Thanks.
ankitraut27 is offline   Reply With Quote

Old   September 15, 2017, 08:51
Default
  #2
Senior Member
 
ksrivast's Avatar
 
Kislaya Srivastava
Join Date: Sep 2017
Location: Convergent Science, Northville MI
Posts: 110
Rep Power: 5
ksrivast is on a distinguished road
Hello Ankit,

Unless you have interfaces in your case setup, the boundary ID 16 would correspond to disconnect triangles. As you might know, CONVERGE creates disconnect triangles between regions during a closed event. However, you must note that the boundaries between which disconnect triangles are created must not be moving when the regions are disconnected.

The error is most likely telling you that you have boundaries associated with these disconnect triangles that are moving during a closed event. For example, this error is present when you define a CLOSE event between the ports and the cylinder while the valves are still moving.

I offer the following suggestions (assuming this case includes motion of valves): Please check to see that your valves have reached minimum lift before you define your CLOSE event. If you're using VALVE events, please make sure you have the (minimum_lift/2) point defined in your valve profile. I would also strongly advise you to use our latest code.

Hope this helps. Please refer the manual for more information on the above.

Sincerely,

Srivastava
ankitraut27 likes this.
__________________
Kislaya Srivastava
Research Engineer | Applications
CONVERGECFD
ksrivast is offline   Reply With Quote

Old   September 15, 2017, 10:51
Default
  #3
New Member
 
Ankit Raut
Join Date: Sep 2017
Location: Chennai
Posts: 14
Rep Power: 5
ankitraut27 is on a distinguished road
Thanks Kislaya for a reply.

I tried this but still I am getting same error. Can I share my case setup file with you for your reference?
ankitraut27 is offline   Reply With Quote

Old   September 15, 2017, 10:59
Default
  #4
Senior Member
 
ksrivast's Avatar
 
Kislaya Srivastava
Join Date: Sep 2017
Location: Convergent Science, Northville MI
Posts: 110
Rep Power: 5
ksrivast is on a distinguished road
Hello Ankit,

Sure. You send your case files (*.in and *.dat files) to support@convergecfd.com . Please use your official email for all correspondence with Convergent Science. Please mention the issues you are facing and add my name as reference.

Sincerely,

Srivastava
__________________
Kislaya Srivastava
Research Engineer | Applications
CONVERGECFD
ksrivast is offline   Reply With Quote

Old   September 15, 2017, 11:03
Default
  #5
New Member
 
Ankit Raut
Join Date: Sep 2017
Location: Chennai
Posts: 14
Rep Power: 5
ankitraut27 is on a distinguished road
Thank You so much
ankitraut27 is offline   Reply With Quote

Old   January 20, 2021, 21:39
Default
  #6
ltl
New Member
 
LTL
Join Date: Jan 2021
Posts: 6
Rep Power: 2
ltl is on a distinguished road
Hello Ankit,

I am getting the same error with which you submited in September 15, 2017.

Error message is as below:
"JOB ABORT invoked by rank 7
ERROR: wrong boundary motion_type in calc_moving_vec boundary id = 15."
Only 14 boundaries in my case, so where dose the boundary 16 come from?

How did you solve this problem in th end? Can you give some advice?

Thanks so much.
ltl is offline   Reply With Quote

Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
bash script for pseudo-parallel usage of reconstructPar kwardle OpenFOAM Post-Processing 39 July 1, 2020 09:13
Problem running in parralel Val OpenFOAM Running, Solving & CFD 1 June 12, 2014 02:47
OpenFOAM compile error balkrishna OpenFOAM Installation 9 June 17, 2011 03:53
Compiling OpenFOAM on hpc-fe.gbar.dtu.dk kaergaard OpenFOAM Installation 1 June 16, 2011 01:33
cfd job Dr. Don I anyanwu Main CFD Forum 20 May 17, 1999 15:13


All times are GMT -4. The time now is 15:23.