 |
 |
 |
|
|
|
[Sponsors] | ||||
October 2, 2017, 15:46
|
injection pressure
|
#1 |
|
Senior Member
amin u3fi
Join Date: Feb 2013
Posts: 137
Rep Power: 13  |
Hello,
I know there is no injection pressure input when simulating diesel engine combustion. So, I entered the mass (3e-6) and injection duration (6 deg) based on experimental data. CONVERGE gave me the injection pressure of 70 bar. However, in experiments, the injection pressure of common rail system is 520 bar. So, I was wondering why converge underpredicts the injection pressure? |
|
|
|
|
|
October 2, 2017, 17:21
|
|
#2 |
|
Member
Tristan Burton
Join Date: Sep 2017
Posts: 92
Rep Power: 8 |
Amin,
What is your engine speed? I guessed 1800 rpm and used 3e-05 kg of IC8H18 in 6 CAD and got an injection pressure of 593 bar from CONVERGE Studio's Spray rate calculator. Are you certain your injected mass is 3 mg and not 30 mg? Best regards, Tristan |
|
|
|
|
|
|
October 2, 2017, 17:26
|
|
#3 | |
|
Senior Member
amin u3fi
Join Date: Feb 2013
Posts: 137
Rep Power: 13 |
Quote:
I'm simulating dual-fuel engine and it's 1/6 of the combustion chamber. The total amount of diesel is 18 mg/cycle c7h16 and for 1/6 sector should be 3 mg/cycle. The engine rpm is 910 and injection duration is 6 deg. |
||
|
|
|
||
|
October 2, 2017, 17:50
|
|
#4 |
|
Member
Tristan Burton
Join Date: Sep 2017
Posts: 92
Rep Power: 8 |
Amin,
What is your injector nozzle diameter? Best regards, Tristan |
|
|
|
|
|
|
October 2, 2017, 17:56
|
|
#5 | |
|
Senior Member
amin u3fi
Join Date: Feb 2013
Posts: 137
Rep Power: 13 |
Quote:
|
||
|
|
|
||
|
October 2, 2017, 18:06
|
|
#6 |
|
Member
Tristan Burton
Join Date: Sep 2017
Posts: 92
Rep Power: 8 |
Amin,
What value are you using for the nozzle discharge coefficient and how are you specifying the velocity coefficient? Best regards, Tristan |
|
|
|
|
|
|
October 2, 2017, 18:12
|
|
#7 | |
|
Senior Member
amin u3fi
Join Date: Feb 2013
Posts: 137
Rep Power: 13 |
Quote:
|
||
|
|
|
||
|
October 2, 2017, 18:22
|
|
#8 |
|
Member
Tristan Burton
Join Date: Sep 2017
Posts: 92
Rep Power: 8 |
Amin,
Ok, I get something similar to your value. However, it seems unlikely that the pressure just upstream of the nozzle holes (what CONVERGE reports) is 520 bar for this combination of parameters. Best regards, Tristan |
|
|
|
|
|
|
October 11, 2017, 07:14
|
|
#9 |
|
Member
Krishna
Join Date: Apr 2012
Posts: 54
Rep Power: 14 |
Hi Trisan,
Can you please suggest, where can i get CONVERGE Studio's Spray rate calculator. Thanks in advance. Best regards, Krishna |
|
|
|
|
|
|
October 11, 2017, 12:21
|
|
#10 |
|
Member
Tristan Burton
Join Date: Sep 2017
Posts: 92
Rep Power: 8 |
Krishna,
It's under the Spray modeling -> Injectors -> Tools button in Studio. Best regards, Tristan |
|
|
|
|
|
|
October 12, 2017, 09:35
|
|
#11 |
|
Member
Krishna
Join Date: Apr 2012
Posts: 54
Rep Power: 14 |
Thank you Trisan.
|
|
|
|
|
|
|
November 6, 2017, 02:43
|
|
#12 |
|
New Member
shelleyvander
Join Date: Nov 2017
Posts: 5
Rep Power: 8 |
My engien speed is 1500 rmp/s but the injector is not like that. Maybe there is something wrong on othe parts
|
|
|
|
|
|
 |
| Thread Tools | Search this Thread |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| question regarding LES of pipe flow - pimpleFoam | Dan1788 | OpenFOAM Running, Solving & CFD | 37 | December 26, 2017 14:42 |
| interFoam (HELYX-OS) pressure boundary conditions | SFr | OpenFOAM Running, Solving & CFD | 8 | June 23, 2016 16:36 |
| Pressure drop due to particle injection | semo | FLUENT | 2 | September 11, 2014 14:12 |
| Calculation of the Governing Equations | Mihail | CFX | 7 | September 7, 2014 06:27 |
| validation data for high pressure transient gas injection | doki | FLUENT | 0 | September 26, 2010 10:48 |
Linear Mode
