|
[Sponsors] |
Setup of Diesel Ethanol Blend fuel in sector simulation |
|
LinkBack | Thread Tools | Search this Thread | Display Modes |
October 5, 2018, 01:44 |
Setup of Diesel Ethanol Blend fuel in sector simulation
|
#1 |
New Member
Kapil
Join Date: Apr 2018
Location: India
Posts: 16
Rep Power: 8 |
Hi all,
I noticed there were more than one species and their mass fractions defined in the injector edit dialog box. Is this the same for defining fuel blends like mixture of diesel and ethanol? If not, are there other ways to do that and how? Thanks! |
|
October 8, 2018, 10:32 |
|
#2 |
Member
Dan Probst
Join Date: Jan 2016
Location: Convergent Science, Madison WI
Posts: 38
Rep Power: 10 |
You can setup multi component fuel blends in CONVERGE.
We have a few examples of how to do this. When you setup multiple species in the injector settings, the liquid species are injected into the domain. You also define in the spray settings how these species evaporate. |
|
October 9, 2018, 04:15 |
|
#3 |
New Member
Kapil
Join Date: Apr 2018
Location: India
Posts: 16
Rep Power: 8 |
I did try as you mentioned.
1. Added C2H5OH in Parcel Simulation & Species 2. Added C2H5OH in the injected parcel species and mass fraction 3. Evaporation Source changed from 0 to 2 - source all base parcel species But the simulation shows this error: JOB ABORT invoked by rank 0: ERROR: error in spray.in, evaporation is on but parcel species for DIESEL2 does not exist as a gas species --------- 1.Also, will the Fuel Species in Combustion Modelling (General) remain as C7H16 even in case of Multi Component? Thanks! |
|
October 9, 2018, 17:38 |
|
#4 | |
Member
Dan Probst
Join Date: Jan 2016
Location: Convergent Science, Madison WI
Posts: 38
Rep Power: 10 |
Quote:
Take a look at the Diesel Sector example case in Studio. In that case we inject DIESEL2 as a liquid, and evaporate it as C7H16 to the gas phase with evap_source_flag = 0. Since you are using a blended fuel of Diesel and Ethanol, I would suggest a multicomponent setup (please look at the Diesel Sector Multicomponent example). In this case you will set up multiple fuels as liquids, set evap_source_flag = 2, and list each fuel with the correct species fraction. It may be you only need to switch DIESEL2 to C7H16 (where heptane is the liquid and gas species representing Diesel2). |
||
October 10, 2018, 03:13 |
|
#5 |
Senior Member
Tobias
Join Date: May 2016
Location: Germany
Posts: 264
Rep Power: 10 |
If you still want to use Diesel2 and not heptane, you can also rename all "C7H16" or "nC7H16" within mech.dat and therm.dat to "Diesel2". Then you can evaporate from liquid to gas species since the names are consistent, while acutally using heptane data for gas phase.
|
|
October 10, 2018, 11:54 |
Issue Resolved !!!
|
#6 |
New Member
Kapil
Join Date: Apr 2018
Location: India
Posts: 16
Rep Power: 8 |
Hey all,
The issue was resolved once i changed from DIESEL2 to C7H16 & added CH5OH in gas species. Thanks for helping out. |
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Heat release of diesel in dual fuel engine simulation | PRJHA | CONVERGE | 1 | March 30, 2017 11:42 |
Simulation of Biodiesel & Diesel fuel blends combustion with AVLFIRE | Rayka.afrouz | Main CFD Forum | 0 | December 4, 2012 06:46 |
some one help me - diesel fuel #2 - fluent | mslu544 | FLUENT | 0 | May 25, 2009 06:50 |
Diesel fuel combustion | Marek | CFX | 1 | November 30, 2008 13:39 |
Fuel Modelling in Diesel Engines, what's truth | Jo | Siemens | 0 | August 18, 2004 13:47 |