JOB ABORT invoked by rank 0

ankitraut27 · September 15, 2017, 07:53

Hello Everyone,

I am getting same error again and again. Error message is as below:
" JOB ABORT invoked by rank 0
ERROR: wrong boundary motion_type in calc_moving_vec boundary id = 16"

What does this error mean? I have only 15 boundaries in my case. Then from where this boundary id 16 came?

Please Help!

Thanks.

ksrivast · September 15, 2017, 08:51

Hello Ankit,

Unless you have interfaces in your case setup, the boundary ID 16 would correspond to disconnect triangles. As you might know, CONVERGE creates disconnect triangles between regions during a closed event. However, you must note that the boundaries between which disconnect triangles are created must not be moving when the regions are disconnected.

The error is most likely telling you that you have boundaries associated with these disconnect triangles that are moving during a closed event. For example, this error is present when you define a CLOSE event between the ports and the cylinder while the valves are still moving.

I offer the following suggestions (assuming this case includes motion of valves): Please check to see that your valves have reached minimum lift before you define your CLOSE event. If you're using VALVE events, please make sure you have the (minimum_lift/2) point defined in your valve profile. I would also strongly advise you to use our latest code.

Hope this helps. Please refer the manual for more information on the above.

Sincerely,

Srivastava

ankitraut27 · September 15, 2017, 10:51

Thanks Kislaya for a reply.

I tried this but still I am getting same error. Can I share my case setup file with you for your reference?

ksrivast · September 15, 2017, 10:59

Hello Ankit,

Sure. You send your case files (*.in and *.dat files) to support@convergecfd.com . Please use your official email for all correspondence with Convergent Science. Please mention the issues you are facing and add my name as reference.

Sincerely,

Srivastava

ankitraut27 · September 15, 2017, 11:03

Thank You so much

ltl · January 20, 2021, 21:39

Hello Ankit,

I am getting the same error with which you submited in September 15, 2017.

Error message is as below:
"JOB ABORT invoked by rank 7
ERROR: wrong boundary motion_type in calc_moving_vec boundary id = 15."
Only 14 boundaries in my case, so where dose the boundary 16 come from?

How did you solve this problem in th end? Can you give some advice?

Thanks so much.

September 15, 2017, 07:53	JOB ABORT invoked by rank 0	#1
ankitraut27 New Member Ankit Raut Join Date: Sep 2017 Location: Chennai Posts: 14 Rep Power: 8	Hello Everyone, I am getting same error again and again. Error message is as below: " JOB ABORT invoked by rank 0 ERROR: wrong boundary motion_type in calc_moving_vec boundary id = 16" What does this error mean? I have only 15 boundaries in my case. Then from where this boundary id 16 came? Please Help! Thanks.

September 15, 2017, 08:51		#2
ksrivast Senior Member Kislaya Srivastava Join Date: Sep 2017 Location: Convergent Science, Northville MI Posts: 165 Rep Power: 8	Hello Ankit, Unless you have interfaces in your case setup, the boundary ID 16 would correspond to disconnect triangles. As you might know, CONVERGE creates disconnect triangles between regions during a closed event. However, you must note that the boundaries between which disconnect triangles are created must not be moving when the regions are disconnected. The error is most likely telling you that you have boundaries associated with these disconnect triangles that are moving during a closed event. For example, this error is present when you define a CLOSE event between the ports and the cylinder while the valves are still moving. I offer the following suggestions (assuming this case includes motion of valves): Please check to see that your valves have reached minimum lift before you define your CLOSE event. If you're using VALVE events, please make sure you have the (minimum_lift/2) point defined in your valve profile. I would also strongly advise you to use our latest code. Hope this helps. Please refer the manual for more information on the above. Sincerely, Srivastava ankitraut27 likes this. __________________ Kislaya Srivastava Principal Research Engineer \| Applications CONVERGECFD

September 15, 2017, 10:59		#4
ksrivast Senior Member Kislaya Srivastava Join Date: Sep 2017 Location: Convergent Science, Northville MI Posts: 165 Rep Power: 8	Hello Ankit, Sure. You send your case files (.in and .dat files) to support@convergecfd.com . Please use your official email for all correspondence with Convergent Science. Please mention the issues you are facing and add my name as reference. Sincerely, Srivastava __________________ Kislaya Srivastava Principal Research Engineer \| Applications CONVERGECFD

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
bash script for pseudo-parallel usage of reconstructPar	kwardle	OpenFOAM Post-Processing	41	August 23, 2023 02:48
Problem running in parralel	Val	OpenFOAM Running, Solving & CFD	1	June 12, 2014 02:47
OpenFOAM compile error	balkrishna	OpenFOAM Installation	9	June 17, 2011 03:53
Compiling OpenFOAM on hpc-fe.gbar.dtu.dk	kaergaard	OpenFOAM Installation	1	June 16, 2011 01:33
cfd job	Dr. Don I anyanwu	Main CFD Forum	20	May 17, 1999 15:13

September 15, 2017, 10:51		#3
ankitraut27 New Member Ankit Raut Join Date: Sep 2017 Location: Chennai Posts: 14 Rep Power: 8	Thanks Kislaya for a reply. I tried this but still I am getting same error. Can I share my case setup file with you for your reference?

September 15, 2017, 11:03		#5
ankitraut27 New Member Ankit Raut Join Date: Sep 2017 Location: Chennai Posts: 14 Rep Power: 8	Thank You so much

January 20, 2021, 21:39		#6
ltl New Member Lynn Join Date: Jan 2021 Posts: 12 Rep Power: 5	Hello Ankit, I am getting the same error with which you submited in September 15, 2017. Error message is as below: "JOB ABORT invoked by rank 7 ERROR: wrong boundary motion_type in calc_moving_vec boundary id = 15." Only 14 boundaries in my case, so where dose the boundary 16 come from? How did you solve this problem in th end? Can you give some advice? Thanks so much.