|
[Sponsors] |
Fatal error in PMPI_Alltoallv: Message truncated, error stack |
|
LinkBack | Thread Tools | Search this Thread | Display Modes |
February 28, 2022, 06:48 |
Fatal error in PMPI_Alltoallv: Message truncated, error stack
|
#1 |
New Member
Hongjie Zhou
Join Date: Feb 2022
Posts: 8
Rep Power: 4 |
Recently I used CONVERGE software to simulate a two-stroke engine, but when the piston moves to 359.494 degrees, the following error occurs:
Abort(742988302) on node 18 (rank 18 in comm 0): Fatal error in PMPI_Alltoallv: Message truncated, error stack: PMPI_Alltoallv(371)............................... ..: MPI_Alltoallv(sbuf=000000001510C 040, scnts=000000000DE83F70, sdispls=000000000DE82B30, dtype=USER<contig>, rbuf =0000000011792570, rcnts=000000000DE82770, rdispls=000000000DE83C70, datatype=d type=USER<contig>, comm=MPI_COMM_WORLD) failed MPIDI_Alltoallv_intra_composition_alpha(1051): MPIDI_NM_mpi_alltoallv(806).................: MPIR_Alltoallv_intra_scattered(127)..........: (unknown)(): Message truncated May I ask where is the problem? Looking forward to your advice. |
|
February 28, 2022, 10:02 |
|
#2 | |
Member
John Etcheverry
Join Date: Dec 2018
Posts: 56
Rep Power: 7 |
Quote:
I can think of a few common problems that you may be able to check, though. I see you're running a two stroke engine - are you running seals? If so, have you checked the quality of your seals? How about the alignment of the piston and liner with the axis of motion - are there any warnings when the simulations starts about alignment? Does this run with check_grid_motion_flag enabled in inputs.in? Thanks! - John |
||
March 1, 2022, 01:46 |
|
#3 | |
New Member
Hongjie Zhou
Join Date: Feb 2022
Posts: 8
Rep Power: 4 |
Quote:
Thank you for your advice. This is my problem during the process of checking the quality of the mesh.There were some early warnings:Can not find split point after sealing.I have properly refined the mesh and still have these warnings and the same error at 359.494 degrees.Are there some rules that need to be followed in the process of setting the seal? I set the distance between the piston edge and the liner to 0.1mm, does that have something to do with it? In addition, the moment when the error occurs is the moment when the piston moves to the TDC and reaches the end of the cylinder, does it have anything to do with this? Thank you again. Hongjie |
||
March 1, 2022, 05:52 |
|
#4 | |
New Member
Hongjie Zhou
Join Date: Feb 2022
Posts: 8
Rep Power: 4 |
Quote:
Hi,John I have solved this problem, thanks for your help. Good luck with your work. Hongjie |
||
Tags |
converge,pmpi_alltoallv |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Message truncated, error stack: MPIDI_CH3U_Receive_data_found | nandiganavishal | OpenFOAM Running, Solving & CFD | 21 | November 19, 2021 01:20 |
simpleFoam parallel | AndrewMortimer | OpenFOAM Running, Solving & CFD | 12 | August 7, 2015 18:45 |
Error message in CFX-10 | CFDworker | CFX | 2 | October 12, 2007 07:23 |
MPI Message truncated | josef | OpenFOAM Running, Solving & CFD | 1 | January 9, 2006 06:29 |
Fatal Error Message | Eric | FLUENT | 0 | February 20, 2004 11:20 |