How to build current blower fan model in Flotherm

eric0722 · January 26, 2015, 03:49

Method 1:Build fan housing geometry and create one fan (smart part) at fan outlet fan construction:rectangular fan and dedine non-linear fan curve

Method 2:Build fan housing geometry and create two fan (smart part) at fan inlet(top&buttom) fan construction:Axial fan and dedine non-linear fan curve

Method 3:Build fan housing geometry and create recirculation devices fan construction one supply and two extract

Question 1:Which way is best method for blower fan?

Question 2:About P-Q curve, Why the fan outlet flow rate can't meet P-Q SPEC? such as SPEC Qmax=15 CFM, but fan outlet flow rate just only 12 CFM

Question 3:When I use method 2, How do I define P-Q curve value for two fan?

Gabriel_C · January 27, 2015, 02:06

hello,

this might be useful: http://webparts.mentor.com/flotherm/...arts/v6blower/

somehow it tells you to use "method 3"

Best regards, Gabriel

namshaheb · November 24, 2020, 09:20

Have you found the solution to your problem? I am also looking for help in this.

hank0301 · January 2, 2021, 02:36

Personally I prefer the method 3.
Both model 1 and 2 will calculate the pressure drop of the fan geometry, that is why the outlet flow rate is lower than P-Q curve.
For model 3, you can define the P-Q same as the original one because recirculation device does not consider the geometry and pressure loss.

January 26, 2015, 03:49	How to build current blower fan model in Flotherm	#1
eric0722 New Member Eric Lin Join Date: Jun 2013 Posts: 1 Rep Power: 0	Method 1:Build fan housing geometry and create one fan (smart part) at fan outlet fan construction:rectangular fan and dedine non-linear fan curve Method 2:Build fan housing geometry and create two fan (smart part) at fan inlet(top&buttom) fan construction:Axial fan and dedine non-linear fan curve Method 3:Build fan housing geometry and create recirculation devices fan construction one supply and two extract Question 1:Which way is best method for blower fan? Question 2:About P-Q curve, Why the fan outlet flow rate can't meet P-Q SPEC? such as SPEC Qmax=15 CFM, but fan outlet flow rate just only 12 CFM Question 3:When I use method 2, How do I define P-Q curve value for two fan? shuisheng likes this.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Superlinear speedup in OpenFOAM 13	msrinath80	OpenFOAM Running, Solving & CFD	18	March 3, 2015 05:36
Centrifugal Fan Model - Frozen Rotor	aulrich	CFX	16	October 16, 2014 05:13
[Pointwise] cannot set "fan" boundary condition to 2D Ducted fan model	brksnn	Pointwise & Gridgen	1	January 11, 2013 09:05
Native fan model?	Vcent	FLUENT	0	December 10, 2012 07:36
how to model sloping fan in Flotherm?	szcaxman	Main CFD Forum	0	July 10, 2004 03:35

January 27, 2015, 02:06		#2
Gabriel_C Member Gabriel Ciobanu Join Date: Jul 2011 Posts: 47 Rep Power: 14	hello, this might be useful: http://webparts.mentor.com/flotherm/...arts/v6blower/ somehow it tells you to use "method 3" Best regards, Gabriel

November 24, 2020, 09:20		#3
namshaheb New Member Nam Shaheb Join Date: Nov 2020 Posts: 3 Rep Power: 5	Have you found the solution to your problem? I am also looking for help in this.

January 2, 2021, 02:36		#4
hank0301 New Member Hank Chung Join Date: Oct 2016 Posts: 5 Rep Power: 9	Personally I prefer the method 3. Both model 1 and 2 will calculate the pressure drop of the fan geometry, that is why the outlet flow rate is lower than P-Q curve. For model 3, you can define the P-Q same as the original one because recirculation device does not consider the geometry and pressure loss.