CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums > Software User Forums > FLOW-3D

Calculating surface roughness correlating with Manning’s n in shallow water model?

Register Blogs Members List Search Today's Posts Mark Forums Read

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old   December 4, 2012, 01:48
Post Calculating surface roughness correlating with Manning’s n in shallow water model?
  #1
New Member
 
max
Join Date: Oct 2011
Posts: 10
Rep Power: 14
max0014 is on a distinguished road
I have difficulty calculating appropriate surface roughness that correlates with Manning’s n of my model,
I used Eq (3) given in Chapter 12 of v10 of FLOW-3D manual, to calculate parameter called ROUGH that correlates with Manning’s n. Manning’s n is known for my simulation. But if I use this ROUGH value in drag coefficient for bottom shear stress in Shallow Water physics of FLOW-3D, the simulation does not yield good match. It seems that for good match, the ROUGH value has to be increased more than 100 times the magnitude given by the above equation. The result with default value of 0.0026 is slightly better but still no way close to measured data. Am I using appropriate equation to calculate roughness which correlates Manning’s n into flow model? I used ROUGH as equal to “btmshr” in shallow water physics of FLOW-3D. Is this correct? Is there a direct way of inputting Manning’s n value into the FLOW-3D model?
Any suggestion is highly appreciated.
Thank you.
max0014 is offline   Reply With Quote

Old   December 5, 2012, 12:16
Default
  #2
Senior Member
 
Jeff Burnham
Join Date: Apr 2010
Posts: 204
Rep Power: 16
JBurnham is on a distinguished road
ROUGH is the physical roughness length for 3-D solutions and laminar shallow water solutions ONLY. When you convert Manning's n to get ROUGH, and use it in shallow water physics, it under-predicts the drag, as you have observed, and must be adjusted to give an equivalent drag, as you have also observed. in v10.0 and later, you can use a turbulent shallow water model, in which case ROUGH is not applied: instead, a drag coefficient BTMSHR is specified, default value 0.0026. This is not a physical roughness length.

BTMSHR = fDARCY/8 ≈ nMANNING^2 g (Sf/Sb) / (Rh^(1/3) αMANNING^2)

fDARCY = D'Arcy friction factor [dimless]
nMANNING = Manning's n [ALWAYS s/m^(1/3)]
g = constant magnitude of gravitational acceleration [m/s^2 or ft/s^2]
Sf = energy gradient (free surface slope) of water [m/m or ft/ft]
Sb = bed gradient (bed slope) of water [m/m or ft/ft]
Sf/Sb = 1.0 (assumed by Manning's equation)
Rh = hydraulic radius (= depth for wide channels, wetted area/wetted perimeter for narrow channels) [m or ft]
αMANNING = 1.0 m^(1/3)/m^(1/3) when Rh & g are in m OR
αMANNING = 1.486 ft^(1/3)/m^(1/3) when Rh & g are in ft.

As you can see, there are different n values for different depths of flow, so the n value and Rh value you use to get BTMSHR must be appropriate for each other AND the flow being modeled.
JBurnham is offline   Reply With Quote

Reply

Tags
flow3d, manning's n, shallow water, surface roughness

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
mass flow in is not equal to mass flow out saii CFX 12 March 19, 2018 06:21
[Gmsh] Error : Self intersecting surface mesh, computing intersections & Error : Impossible velan OpenFOAM Meshing & Mesh Conversion 3 October 22, 2015 12:05
Calculating forces on a non-closed surface ScottN FLUENT 0 March 1, 2011 18:18
How to update polyPatchbs localPoints liu OpenFOAM Running, Solving & CFD 6 December 30, 2005 18:27
sw for 2D free surface shallow water? Rob Snel Main CFD Forum 7 August 4, 2000 12:03


All times are GMT -4. The time now is 01:00.