CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums > Software User Forums > FLOW-3D

Restart for Solidification

Register Blogs Members List Search Today's Posts Mark Forums Read

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old   May 6, 2009, 04:21
Default Restart for Solidification
  #1
New Member
 
Atul Verma
Join Date: Apr 2009
Location: Bangalore
Posts: 17
Rep Power: 16
atulverma is on a distinguished road
hi!
I am facing a problem with restart for solidification.
After filling the die when I am giving restart for solidification after few time steps its shows the solid fraction as 1 or 0 and the temperature also goes to some maximum value and some where it goes to zero.Thus after few more iterations it shoes negative temperature and the solution ends.
I am using the same grid(multi mesh block) for restart.
I am keeping the air entrainment model on even during solidification and turning on the density as the function of temperature and scalar(solute).
Segregation model is on during filling as well as during solidification.
What all things should be taken care of when giving a restart?

Atul
atulverma is offline   Reply With Quote

Old   May 6, 2009, 15:36
Default
  #2
Member
 
MC
Join Date: Mar 2009
Posts: 56
Rep Power: 17
melissa is on a distinguished road
Hi~
What are your boundary conditions for the restart do you still have velocity?
MC
melissa is offline   Reply With Quote

Old   May 6, 2009, 18:13
Default
  #3
New Member
 
Atul Verma
Join Date: Apr 2009
Location: Bangalore
Posts: 17
Rep Power: 16
atulverma is on a distinguished road
hi melissa!
thanks for replying..here is the further explanation...
No ,I am using symmetry boundary conditions,I used a shot sleeve arrangement to fill the die and the boundaries and the boundary conditions remains same.I give restart little before the complete filling and in the restart simulation after few time steps the piston attains 0 velocity.Also the pressure iterations do not converge as the piston is still pushing the fluid after the die is completely filled.So after some iterations compressibility is invoked.I am switching on the density as a function of temperature and scalar(solute) only in the restart.
The simulation is terminated with " negative fluid temperature" message.Also the temperature before goes to value near Melting point of the pure Solvent in most of the parts and remaining it shows zero temperature.Also the solution well runs for zero velocity field.

1)Is this due to failure of pressure iterations,but I do not see any relation?
2)Air Entrainment Model should be used while modeling solidification or not?
3)Restart based on temperature and internal energy have any effect on the solution?
4)Having multi mesh blocks during solidification creates problem..?

It seems that the temperature and internal energy and thus the solid fraction are not calculated properly.
thanks
Atul
atulverma is offline   Reply With Quote

Old   May 6, 2009, 18:40
Default
  #4
Member
 
MC
Join Date: Mar 2009
Posts: 56
Rep Power: 17
melissa is on a distinguished road
Hi~
The reason for the pressure iterations is such that since you have a velocity boundary at the restart fluid will continue to be pushed through causing pressure iterations. Use fill fraction for fill conditions when filling. Model setup tab.
Then for restart turn off the density evaluation and set the boundary to symmetry.
MC
melissa is offline   Reply With Quote

Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
v4 restart bug optima prime Siemens 3 February 2, 2009 23:51
Restart of FSI simulation V. Kumar CFX 3 July 20, 2006 14:23
restart & ecd files cirilo Siemens 0 November 21, 2005 13:15
transient restart Pete Siemens 1 July 22, 2005 09:11
restart Dmitry Siemens 0 March 22, 2002 11:28


All times are GMT -4. The time now is 07:47.