Active and Passive cells

ati_ros61 · April 4, 2010, 22:05

Dear Experts
I am using Ver 9.4 and we have a license with limitation up to 200,000 cells. however when I defined a mesh about 150,000 cells, the preprocessing is stoped and there is a message that the total number of active and passive cells is above 200,000 and I cannot run the simulation. I dont know what is the meaning of active and passive cells and why the numbers of these quantities more than total mesh that I defined?? how can I run the simulations with 200,000 cells?

Regards
Atiieh

Ghirghidov · April 5, 2010, 03:10

Dear Atiieh Rostami

As I understood your problem right you have to take into account boundary cells. so amount of the cells will increase.

Regards, Armen

ati_ros61 · April 5, 2010, 03:22

Dear Armen A. Ghirghidov
Thank you for your attention.unfortunately I do not understand your suggestion exactly. I just define the number of cells in each directions and I don't know what should I do for this case?

Regards
Atiieh

Ghirghidov · April 5, 2010, 03:39

Dear Atiieh Rostami,

I mean boundary conditions have one or two cell layers. If you want to simulate volume 10x10x10=1000 cells (for example) you will get 12x12x12=1728 cells. Hope this will explain.

Regards, Armen.

April 4, 2010, 22:05	Active and Passive cells	#1
ati_ros61 New Member Atiieh Rostami Join Date: Oct 2009 Location: malaysia Posts: 17 Rep Power: 16	Dear Experts I am using Ver 9.4 and we have a license with limitation up to 200,000 cells. however when I defined a mesh about 150,000 cells, the preprocessing is stoped and there is a message that the total number of active and passive cells is above 200,000 and I cannot run the simulation. I dont know what is the meaning of active and passive cells and why the numbers of these quantities more than total mesh that I defined?? how can I run the simulations with 200,000 cells? Regards Atiieh

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
PROBLEM: Scalar mass fraction	Lorenzo	Siemens	1	July 14, 2008 03:50
passive scalar boundaries	ultrich	Siemens	0	July 12, 2005 11:20
inf thin cells	cmv	Siemens	1	March 13, 2005 13:46

April 5, 2010, 03:10		#2
Ghirghidov Member Armen A. Ghirghidov Join Date: Mar 2009 Posts: 50 Rep Power: 17	Dear Atiieh Rostami As I understood your problem right you have to take into account boundary cells. so amount of the cells will increase. Regards, Armen

April 5, 2010, 03:22		#3
ati_ros61 New Member Atiieh Rostami Join Date: Oct 2009 Location: malaysia Posts: 17 Rep Power: 16	Dear Armen A. Ghirghidov Thank you for your attention.unfortunately I do not understand your suggestion exactly. I just define the number of cells in each directions and I don't know what should I do for this case? Regards Atiieh

April 5, 2010, 03:39		#4
Ghirghidov Member Armen A. Ghirghidov Join Date: Mar 2009 Posts: 50 Rep Power: 17	Dear Atiieh Rostami, I mean boundary conditions have one or two cell layers. If you want to simulate volume 10x10x10=1000 cells (for example) you will get 12x12x12=1728 cells. Hope this will explain. Regards, Armen.