segmentation fault dpm force

zahrae · June 13, 2019, 08:35

Hello!
I create a program for a new expression of a thermophoretic force (code in two parts: one for the thermophoretic coefficient and the other one in the force).
when I compile it, it gives an error segmentation fault, I figure it out that I should enable this force in the dpm panel for being able to hook the thermophoretic coefficient.
After that, no error was generated, but I think it would be wrong because fluent will consider 2 expressions of thermophoretic force, the default one and the force I hooked by the UDF is that so?
can you please guide me! I am so confused.

AlexanderZ · June 14, 2019, 00:48

fluent uses UDF if it is hooked properly

best regards

zahrae · June 14, 2019, 19:05

Before hooking the thermophoretic force I should hook the thermophoretic coefficient because my force depend on it, and the only way to hook this coefficient is to enable the thermophoretic force present in physical models. By this method fluent will considere to thermophoretic forces?
I have tried to create a new material (inert particle) with a thermo coefficent as a new physical property ( for being able to hook my udf )but it shows only the density and heat capacity after the creation of material.

Is there an other way to hook the thermophoretic coefficient?

zahrae · June 17, 2019, 16:51

please, any help!! Thanks in advance .

June 13, 2019, 08:35	segmentation fault dpm force	#1
zahrae Member imane Join Date: Aug 2018 Posts: 61 Rep Power: 7	Hello! I create a program for a new expression of a thermophoretic force (code in two parts: one for the thermophoretic coefficient and the other one in the force). when I compile it, it gives an error segmentation fault, I figure it out that I should enable this force in the dpm panel for being able to hook the thermophoretic coefficient. After that, no error was generated, but I think it would be wrong because fluent will consider 2 expressions of thermophoretic force, the default one and the force I hooked by the UDF is that so? can you please guide me! I am so confused.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
ActuatorDiskExplicitForce in OF2.1. Help	be_inspired	OpenFOAM Programming & Development	10	September 14, 2018 11:12
Segmentation fault in SU2 V5.0	ygd	SU2	2	March 1, 2017 04:38
DPM Segmentation Fault in UDF	jhlee9622	FLUENT	0	July 1, 2016 03:21
segmentation fault when installing OF-2.1.1 on a cluster	Rebecca513	OpenFOAM Installation	9	July 31, 2012 15:06
Force can not converge	colopolo	CFX	13	October 4, 2011 22:03

June 14, 2019, 00:48		#2
AlexanderZ Senior Member Alexander Join Date: Apr 2013 Posts: 2,363 Rep Power: 34	fluent uses UDF if it is hooked properly best regards

June 14, 2019, 19:05		#3
zahrae Member imane Join Date: Aug 2018 Posts: 61 Rep Power: 7	Before hooking the thermophoretic force I should hook the thermophoretic coefficient because my force depend on it, and the only way to hook this coefficient is to enable the thermophoretic force present in physical models. By this method fluent will considere to thermophoretic forces? I have tried to create a new material (inert particle) with a thermo coefficent as a new physical property ( for being able to hook my udf )but it shows only the density and heat capacity after the creation of material. Is there an other way to hook the thermophoretic coefficient?

June 17, 2019, 16:51		#4
zahrae Member imane Join Date: Aug 2018 Posts: 61 Rep Power: 7	please, any help!! Thanks in advance .