Dynamic mesh

Arty · March 7, 2013, 05:18

I am not really a Fluent whiz, so, here is a question:
Is it ok to make a two-way FSI considering a gas compressor blade using Fluid Flow (Fluent) with Dynamic Mesh turned off or the Fsi doesn't make sence in this case?
I did not use dynamic mesh because otherwise I got messages about negative cell volume and I'm tired trying to make it positive)).

A_Lyaskin · March 7, 2013, 07:15

When you turn off dynamic mesh, you get one-way FSI instead of two-way. So it's better to find the reason of negative cell volume messages. Usually it means that your time step is too big. Or you've messed something in dynamic mesh methods...

fluent87 · March 7, 2013, 09:48

Hi,
try to change the layer dimension (from dynamic mesh menu) or the mesh cell dimension . Usually there is a problem in the dynamic mesh direction. Tray to create a mesh for layer (on a plane e extrude for alla lenght).

Arty · March 7, 2013, 22:01

Thanks for the replies guys.
I think that the time step is small enough, and so I tried different Mesh Methods, but there is a new problem:
Couldn't intersect threads 7 and 8.
Can you tell what's this about?

By the way, I didn't really get anything about layer dimension or the mesh cell dimension, or a mesh for layer. I looked through the fluent tabs, but didn't find anything about, so could you tell me what you meant?

March 7, 2013, 05:18	Dynamic mesh	#1
Arty New Member Join Date: Mar 2013 Posts: 5 Rep Power: 13	I am not really a Fluent whiz, so, here is a question: Is it ok to make a two-way FSI considering a gas compressor blade using Fluid Flow (Fluent) with Dynamic Mesh turned off or the Fsi doesn't make sence in this case? I did not use dynamic mesh because otherwise I got messages about negative cell volume and I'm tired trying to make it positive)).

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Dynamic Mesh on Pintle type injector.	herntan	FLUENT	16	September 4, 2020 08:27
pls help. mesh collapsed with dynamic mesh.	wlt_1985	FLUENT	2	May 7, 2020 10:42
Incylinder dynamic mesh with volumetric reaction	mas	FLUENT	4	May 3, 2012 10:22
dynamic mesh on a hexa grid	Manoj Kumar	FLUENT	0	August 21, 2007 07:41
Dynamic mesh + grid adapt = Crash! (Files included	BillH	FLUENT	4	July 24, 2007 15:31

March 7, 2013, 07:15		#2
A_Lyaskin Member Anton Lyaskin Join Date: Mar 2009 Location: Samara, Russia Posts: 66 Rep Power: 17	When you turn off dynamic mesh, you get one-way FSI instead of two-way. So it's better to find the reason of negative cell volume messages. Usually it means that your time step is too big. Or you've messed something in dynamic mesh methods...

March 7, 2013, 09:48		#3
fluent87 New Member Cristiano Join Date: Feb 2013 Posts: 11 Rep Power: 13	Hi, try to change the layer dimension (from dynamic mesh menu) or the mesh cell dimension . Usually there is a problem in the dynamic mesh direction. Tray to create a mesh for layer (on a plane e extrude for alla lenght).

March 7, 2013, 22:01		#4
Arty New Member Join Date: Mar 2013 Posts: 5 Rep Power: 13	Thanks for the replies guys. I think that the time step is small enough, and so I tried different Mesh Methods, but there is a new problem: Couldn't intersect threads 7 and 8. Can you tell what's this about? By the way, I didn't really get anything about layer dimension or the mesh cell dimension, or a mesh for layer. I looked through the fluent tabs, but didn't find anything about, so could you tell me what you meant?