mesh quality

jamalf64 · May 2, 2013, 06:34

is good this mesh quality?

Best Regards

RodriguezFatz · May 2, 2013, 06:53

Orthogonal quality isn't the only reasonable criterion for a mesh. Also it depends on what you want to do. Post a picture of your setup and give some information about it and what you use for meshing!

jamalf64 · May 2, 2013, 07:08

Quote:

Originally Posted by RodriguezFatz

Orthogonal quality isn't the only reasonable criterion for a mesh. Also it depends on what you want to do. Post a picture of your setup and give some information about it and what you use for meshing!

Thank to your reply
you can see that here:
http://www.cfd-online.com/Forums/ans...k-meshing.html

RodriguezFatz · May 2, 2013, 07:16

Orthogonal quality of 0.4 isn't bad per se. Do you face convergence difficulties, or why are you asking?

jamalf64 · May 2, 2013, 07:29

Quote:

Originally Posted by RodriguezFatz

Orthogonal quality of 0.4 isn't bad per se. Do you face convergence difficulties, or why are you asking?

Thanks
I asked you Because I encountered to wrong answers.

RodriguezFatz · May 2, 2013, 07:53

Can you elaborate on this a bit? Post some relevant pictures...

jamalf64 · May 2, 2013, 08:09

Quote:

Originally Posted by RodriguezFatz

Can you elaborate on this a bit? Post some relevant pictures...

I am doing free surface simulation of stirred tank. My answers are wrong in compare with the paper. I delet all cas&dat file because I knew they were wrong and I have not any pictures, now

Thanks in advance

RodriguezFatz · May 2, 2013, 08:41

Then I don't see how anyone can help here... hopefully, I am wrong.

May 2, 2013, 06:53		#2
RodriguezFatz Senior Member Philipp Join Date: Jun 2011 Location: Germany Posts: 1,297 Rep Power: 26	Orthogonal quality isn't the only reasonable criterion for a mesh. Also it depends on what you want to do. Post a picture of your setup and give some information about it and what you use for meshing! __________________ The skeleton ran out of shampoo in the shower.

May 2, 2013, 07:16		#4
RodriguezFatz Senior Member Philipp Join Date: Jun 2011 Location: Germany Posts: 1,297 Rep Power: 26	Orthogonal quality of 0.4 isn't bad per se. Do you face convergence difficulties, or why are you asking? jamalf64 likes this. __________________ The skeleton ran out of shampoo in the shower.

May 2, 2013, 07:53		#6
RodriguezFatz Senior Member Philipp Join Date: Jun 2011 Location: Germany Posts: 1,297 Rep Power: 26	Can you elaborate on this a bit? Post some relevant pictures... __________________ The skeleton ran out of shampoo in the shower.

May 2, 2013, 08:41		#8
RodriguezFatz Senior Member Philipp Join Date: Jun 2011 Location: Germany Posts: 1,297 Rep Power: 26	Then I don't see how anyone can help here... hopefully, I am wrong. __________________ The skeleton ran out of shampoo in the shower.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[snappyHexMesh] No layers in a small gap	bobburnquist	OpenFOAM Meshing & Mesh Conversion	6	August 26, 2015 09:38
Polyhedral Mesh Quality in Star-CCM+	niazaliahmed	STAR-CCM+	3	March 8, 2012 13:51
[ICEM] Tetra mesh quality before and after prism layer	Chander	ANSYS Meshing & Geometry	0	December 25, 2011 22:04
fluent add additional zones for the mesh file	SSL	FLUENT	2	January 26, 2008 11:55
Icemcfd 11: Loss of mesh from surface mesh option?	Joe	CFX	2	March 26, 2007 18:10