How To Stop The Iteration Process?

sefde · July 12, 2012, 07:49

Hi everyone,

Can someone please tell me how to stop the iteration process that is being run?

Best regards

Sefde

Bionico · July 12, 2012, 07:59

Hello,
quite simple: Ctrl + C

sefde · July 12, 2012, 08:20

Quote:

Originally Posted by Bionico

Hello,
quite simple: Ctrl + C

Isn't cancel and stop is different?

In my opinion, cancel is to cancel the whole process and
stop is like a stop right where you are.

Bionico · July 12, 2012, 08:41

Ctrl + C (like the button in the picture) just stops your iterating process: you can resume it clicking on Calculate and it starts from the last iteration completed.

In order to cancel the data you have to put the CASE & DATA files in the bin

RodriguezFatz · July 24, 2012, 10:30

Quote:

Originally Posted by Bionico

Ctrl + C (like the button in the picture) just stops your iterating process: you can resume it clicking on Calculate and it starts from the last iteration completed.

In order to cancel the data you have to put the CASE & DATA files in the bin

Is there any way, for transient calculation, to stop iterations of the current timestep and to resume at exactly that point? When I hit the "Cancel" button, fluent will stop the calculation, but when I then hit "Calculate" a new timestep begins instead of doing the iterations of the current one.

Marion · July 25, 2012, 01:49

Hi,
If there is a way I never found it!

I just save the case and data files automatically. When I am debugging a model, I save them every time step so that I can start again from where I want.
Marion.

RodriguezFatz · July 25, 2012, 02:18

Sounds like a no-brainer. Unfortunately, this did not come to my mind...

y series · September 20, 2018, 16:42

hi everyone
i am working in ansys and i want to do half of my iterations in other computer can any body help please?

AlexanderZ · September 20, 2018, 20:59

Quote:

Originally Posted by y series

hi everyone
i am working in ansys and i want to do half of my iterations in other computer can any body help please?

write case and data, then read it on other computer

best regards

Mahya ch · November 19, 2023, 03:02

Quote:

Originally Posted by Bionico

Hello,
quite simple: Ctrl + C

It doesn’t work for me, is there any way to stop calculation? (I need the results and I don’t want to end task in task manager).

July 12, 2012, 07:49	How To Stop The Iteration Process?	#1
sefde New Member nimbus Join Date: Nov 2011 Posts: 23 Rep Power: 14	Hi everyone, Can someone please tell me how to stop the iteration process that is being run? Best regards Sefde

July 25, 2012, 01:49		#6
Marion Senior Member Marion Join Date: Jul 2012 Location: France Posts: 122 Rep Power: 14	Hi, If there is a way I never found it! I just save the case and data files automatically. When I am debugging a model, I save them every time step so that I can start again from where I want. Marion. RodriguezFatz likes this.

September 20, 2018, 16:42	how to stop iteration in middle and resume it next computer from same stopped step?	#8
y series New Member y series Join Date: Sep 2018 Posts: 2 Rep Power: 0	hi everyone i am working in ansys and i want to do half of my iterations in other computer can any body help please?

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
How to force Fluent to stop mid-iteration	matchoo87	FLUENT	1	August 30, 2009 13:04
Stop iteration and continuation of the process	martapajon	OpenFOAM Running, Solving & CFD	3	November 5, 2007 15:06
Parallel runs slower with MTU=9000 than MTU=1500	Javier Larrondo	FLUENT	0	October 28, 2007 22:30
How to stop iteration with TUI?	sophie	FLUENT	4	November 23, 2006 05:18
Heat exchanger problem	chiseung	FLUENT	16	October 20, 2001 04:36

July 12, 2012, 07:59		#2
Bionico Senior Member Flavio Join Date: Sep 2011 Location: Brescia, Italy Posts: 181 Rep Power: 15	Hello, quite simple: Ctrl + C

July 12, 2012, 08:41		#4
Bionico Senior Member Flavio Join Date: Sep 2011 Location: Brescia, Italy Posts: 181 Rep Power: 15	Ctrl + C (like the button in the picture) just stops your iterating process: you can resume it clicking on Calculate and it starts from the last iteration completed. In order to cancel the data you have to put the CASE & DATA files in the bin

July 25, 2012, 02:18		#7
RodriguezFatz Senior Member Philipp Join Date: Jun 2011 Location: Germany Posts: 1,297 Rep Power: 26	Sounds like a no-brainer. Unfortunately, this did not come to my mind...