CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums > Software User Forums > ANSYS > FLUENT

How to solve natural convection problem in fluent?

Register Blogs Members List Search Today's Posts Mark Forums Read

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old   October 9, 2010, 10:59
Default How to solve natural convection problem in fluent?
  #1
New Member
 
subho
Join Date: Oct 2010
Posts: 3
Rep Power: 15
samantasubho is on a distinguished road
Friends, I am trying to solve a natural convection problem in FLUENT (natural convection from a horizontal flat plate) with prescribed wall heat flux.
For the problem I have given the boundary conditions as: left and right part of control volume: pressure inlet and top part of the control volume pressure outlet, wall prescribed heat flux.The fluid is air with Pr=0.7
After 1300 iterations also my solution is not converging. Kindly help me if possible.
samantasubho is offline   Reply With Quote

Old   October 18, 2010, 08:39
Default
  #2
New Member
 
Erik Hultman
Join Date: Apr 2010
Posts: 2
Rep Power: 0
hultman is on a distinguished road
I assume that it is a steady-state run, or do you mean 1300 outer iterations?
hultman is offline   Reply With Quote

Old   October 21, 2010, 05:41
Default
  #3
Member
 
Logan Page
Join Date: Sep 2010
Posts: 38
Rep Power: 15
Logan Page is on a distinguished road
add an image of your mesh and BC's if u can.
Logan Page is offline   Reply With Quote

Old   September 3, 2012, 13:06
Default
  #4
New Member
 
sa
Join Date: Jul 2012
Posts: 23
Rep Power: 13
saharesobh is on a distinguished road
Hello,

I am trying to solve the natural convection (mixed convection) in a Chemical vapor deposition reactor. The reactor has top and bottom plates and inlet and outlet tubes. The reactor is heated by top smaller rectangular plate embodying two heating rod. the top plate is at 250 oc and the bottom plate is at 150 oc. So because of temperature gradient, the natural convection will occurs. When I go to the boundary condition, then I go to hot plate, I see the heat flux (w/m2) and the heat generation rate (w/m3). My question is that, should I need to get the heat flux and geat generation and then put them in Fluent or the fluent get them? would you please give me some advice. I don't know why I cannot see the roll-type flow between two parallel plate?As for heat trasnfer coefficient, I don't know how can I get it? I am really confused .
saharesobh is offline   Reply With Quote

Old   September 4, 2012, 07:09
Default
  #5
New Member
 
Elias Paez
Join Date: Nov 2011
Location: Madrid
Posts: 25
Rep Power: 14
sicfred is on a distinguished road
HI Saharesobh,

First, when you go to boundary conditions hot plate, you just need to put the temperature in the plate, if you put heat flux or heat generation rate you are changing the boundary condition of your plate; this two values are going to be calculate by fluent after you running the simulation (for example in wall fluxes).

Second, if i understood your hot plate is in the top and the cold plate is in the botton, that means that there is not natural convection, you need the heat source in the bottom (or change the direction of the gravity XD)



Quote:
Originally Posted by saharesobh View Post
Hello,

I am trying to solve the natural convection (mixed convection) in a Chemical vapor deposition reactor. The reactor has top and bottom plates and inlet and outlet tubes. The reactor is heated by top smaller rectangular plate embodying two heating rod. the top plate is at 250 oc and the bottom plate is at 150 oc. So because of temperature gradient, the natural convection will occurs. When I go to the boundary condition, then I go to hot plate, I see the heat flux (w/m2) and the heat generation rate (w/m3). My question is that, should I need to get the heat flux and geat generation and then put them in Fluent or the fluent get them? would you please give me some advice. I don't know why I cannot see the roll-type flow between two parallel plate?As for heat trasnfer coefficient, I don't know how can I get it? I am really confused .
sicfred is offline   Reply With Quote

Old   September 5, 2012, 14:04
Default
  #6
New Member
 
sa
Join Date: Jul 2012
Posts: 23
Rep Power: 13
saharesobh is on a distinguished road
Thank you so much for your response.

You are absolutely right. You know I asked my advisor about this problem( As you said the hot wall cannot be on the top ). She said this roll-type flow is made due to the momentum and prandtl number.Because I am using HTB fluent ( Hafnium tetra Butoxide). Due to these reasons I have natural convection and roll-type flow, Is it alright if I send you my file and you look at that? I can give you my email adress if it is Ok with you. Thank you so much in advance
saharesobh is offline   Reply With Quote

Old   October 14, 2012, 09:20
Default
  #7
Member
 
sagila
Join Date: May 2012
Posts: 39
Rep Power: 13
sagila is on a distinguished road
Hi saharesobh,

I have a tall room with a hot roof that natural convection occurs in it. The side walls are at the same temperature and the floor is adiabatic. I have problem for converging it. Could you please let me know whether you have problem with convergence for your case which is similar to my case? If yes, could you please let me know how you solved it?

Thank you in advance.

Last edited by sagila; October 14, 2012 at 16:09.
sagila is offline   Reply With Quote

Old   April 17, 2014, 03:07
Default
  #8
Senior Member
 
Svetlana Tkachenko
Join Date: Oct 2013
Location: Australia, Sydney
Posts: 407
Rep Power: 14
Светлана is on a distinguished road
I have same issue, I'm sure you solved it back then?
Светлана is offline   Reply With Quote

Reply

Tags
problem naturalconvection

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Natural convection in Fluent smpandey Main CFD Forum 3 February 26, 2010 02:28
natural convection problem in cfx NVSD BABU CFX 7 November 13, 2008 11:56
Can FLUENT solve this type of problem? Whitaker FLUENT 3 October 23, 2000 04:01
Meshing a natural convection problem sandeepmishra FLUENT 1 May 31, 2000 15:36
extremely simple problem... can you solve it properly? Mikhail Main CFD Forum 40 September 9, 1999 10:11


All times are GMT -4. The time now is 04:11.