Particle Injection Flow Rate [kg/m2-s]

Manathan · May 4, 2015, 10:49

Hello everyone,

I would like to know how to get the injection flow rate for each particle meaning that I put in INPUT the mass flow rate [kg/s] but I need to obtain its value normalized by an area in the same way the udf "DPM_EROSION" macro does : mdot/face_area .

Since I'm simulating 2D axisymmetric, the face_area of this udf is unclear for this case. And therefore the area I should use at injection is also unclear.

Thank you !

`e` · May 4, 2015, 18:31

If each particle of an injection stream has a unique mass flow rate you may need to inject your particles using a file instead of the other options such as from a surface or line.

If you're simulating in 2-D then you could use a length of 1 m in the third direction.

Manathan · May 5, 2015, 03:09

mmm since I'm using a linear space repartition, i thought that using a linear distribution of the mass flow rate would be sufficient.
I'll try to do that then, thank you. Also in 2D axisymmetric, I think I've discovered that the DPM_EROSION macro gives the flow rate : mdot/area with an area for 1 radian. So I thought that I would use for the area of each stream in position r the following equation :

mass flow rate = flow rate * (2*r*dr)

with dr being half the distance between each stream. This area correspond to 1 radian.

I don't have the time to check right now, so if someone knows if it's true it would be great, otherwise I will post my results later on.

May 4, 2015, 10:49	Particle Injection Flow Rate [kg/m2-s]	#1
Manathan New Member Join Date: Apr 2015 Posts: 28 Rep Power: 11	Hello everyone, I would like to know how to get the injection flow rate for each particle meaning that I put in INPUT the mass flow rate [kg/s] but I need to obtain its value normalized by an area in the same way the udf "DPM_EROSION" macro does : mdot/face_area . Since I'm simulating 2D axisymmetric, the face_area of this udf is unclear for this case. And therefore the area I should use at injection is also unclear. Thank you !

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
DEM - Post Processing : Particle Mass Flow Rate	yesaswi92	STAR-CCM+	4	August 27, 2014 15:23
How to change from mass flow to volume flow rate	stanley	FLUENT	1	February 2, 2007 06:44
Particle mass flow rate	Jeff	CFX	3	September 17, 2004 10:46
DPM mass flow rate	Szabolcs Varga	FLUENT	3	May 6, 2004 15:21
liquid particle track and flow rate	Tim	FLUENT	1	November 28, 2001 21:41

May 4, 2015, 18:31		#2
`e` Senior Member Join Date: Mar 2015 Posts: 892 Rep Power: 18	If each particle of an injection stream has a unique mass flow rate you may need to inject your particles using a file instead of the other options such as from a surface or line. If you're simulating in 2-D then you could use a length of 1 m in the third direction.

May 5, 2015, 03:09		#3
Manathan New Member Join Date: Apr 2015 Posts: 28 Rep Power: 11	mmm since I'm using a linear space repartition, i thought that using a linear distribution of the mass flow rate would be sufficient. I'll try to do that then, thank you. Also in 2D axisymmetric, I think I've discovered that the DPM_EROSION macro gives the flow rate : mdot/area with an area for 1 radian. So I thought that I would use for the area of each stream in position r the following equation : mass flow rate = flow rate * (2rdr) with dr being half the distance between each stream. This area correspond to 1 radian. I don't have the time to check right now, so if someone knows if it's true it would be great, otherwise I will post my results later on.