How to resume monitoring after a pause in Fluent?

FaSe · January 20, 2017, 12:17

Hi all
I monitor drag, lift and momentum in ANSYS Fluent (plot and write) and save the project. After restarting computer, when I want to continue the solution, drag, lift and momentum monitors start from beginning. How can I resume monitoring? (i.e begin from last saved status)

Kushal Puri · January 20, 2017, 12:21

Quote:

Originally Posted by FaSe

Hi all
I monitor drag, lift and momentum in ANSYS Fluent (plot and write) and save the project. After restarting computer, when I want to continue the solution, drag, lift and momentum monitors start from beginning. How can I resume monitoring? (i.e begin from last saved status)

You are continuing your simulation or you are simulating it again from fresh?

FaSe · January 21, 2017, 09:29

Hi Kushal Puri,
I am continuing my simulation after restarting the computer.

Kushal Puri · January 23, 2017, 06:05

Quote:

Originally Posted by FaSe

Hi Kushal Puri,
I am continuing my simulation after restarting the computer.

Then it will automatically start the monitors from the last iterations, but when u start the simulation it will ask whether to update monitor or not, just put ok

FaSe · January 24, 2017, 02:03

Thank you for your reply Kushal Puri,

When i restart the simulation, it asks that "save changes to this simulation only" and "save changes to this and future simulations", no matter which one is selected, but when it starts running, previous monitors disappear and monitors start from beginning. i am writing the monitor files, and plot them in Excel. i simulate a transient simulation, so the arrangement of time steps is important. (i.e time steps should be Continuous). I have this problem when there is blackout and computer turns off.

Thank you again, for your kindness.

January 20, 2017, 12:17	How to resume monitoring after a pause in Fluent?	#1
FaSe New Member LordF Join Date: Jan 2016 Posts: 18 Rep Power: 10	Hi all I monitor drag, lift and momentum in ANSYS Fluent (plot and write) and save the project. After restarting computer, when I want to continue the solution, drag, lift and momentum monitors start from beginning. How can I resume monitoring? (i.e begin from last saved status)

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
How to pause a transient simulation and resume without time step advancement?	aleisia	Main CFD Forum	33	June 12, 2017 11:41
What the differences flow equation of Fluent 6.3 and Fluent 12.1	opehterinar81	FLUENT	0	August 19, 2011 11:55
Adding a pause to a fluent journal	Baoun	FLUENT	0	April 24, 2006 04:44
resume and run fluent for another timestep via a c	greg	FLUENT	2	June 30, 2005 05:01
How to resume the parameter of fluent??	scubme	FLUENT	0	January 9, 2005 22:23

January 21, 2017, 09:29		#3
FaSe New Member LordF Join Date: Jan 2016 Posts: 18 Rep Power: 10	Hi Kushal Puri, I am continuing my simulation after restarting the computer.

January 24, 2017, 02:03		#5
FaSe New Member LordF Join Date: Jan 2016 Posts: 18 Rep Power: 10	Thank you for your reply Kushal Puri, When i restart the simulation, it asks that "save changes to this simulation only" and "save changes to this and future simulations", no matter which one is selected, but when it starts running, previous monitors disappear and monitors start from beginning. i am writing the monitor files, and plot them in Excel. i simulate a transient simulation, so the arrangement of time steps is important. (i.e time steps should be Continuous). I have this problem when there is blackout and computer turns off. Thank you again, for your kindness.