|
[Sponsors] |
How to capture static pressure along any section of a pipe? |
|
LinkBack | Thread Tools | Search this Thread | Display Modes |
June 2, 2017, 09:44 |
How to capture static pressure along any section of a pipe?
|
#1 |
New Member
Join Date: May 2017
Posts: 8
Rep Power: 8 |
I am modelling a 3D 90 degree bend so that I can estimate the friction loss coefficient for the pipe fitting (excluding the major friction caused by straight pipe). In order to do so, I need the static pressure values at the ends of the straight pipe section. Can guide me on how to get the values please? Thanks
|
|
June 3, 2017, 12:10 |
|
#2 |
Senior Member
Join Date: Dec 2016
Posts: 152
Rep Power: 10 |
Can you post a graphic describing your problem? What you call "the ends of the straight pipe section" might mean the inlet and outlet of the geometry, or it could mean the point where the pipe switches from straight to starting to bend.
The good news is that it might be simple to help you, regardless of where the ends of the straight pipe are located. |
|
June 4, 2017, 00:55 |
|
#3 | |
New Member
Join Date: May 2017
Posts: 8
Rep Power: 8 |
Quote:
Here is a picture of what I was trying to convey. |
||
June 4, 2017, 22:02 |
|
#4 |
Senior Member
Lucky
Join Date: Apr 2011
Location: Orlando, FL USA
Posts: 5,668
Rep Power: 65 |
You need to clarify what you mean by static pressure at the two points, do you actually mean points or a general region at the axial location?
For points, create a surface monitor (a point monitor). Then there are many ways grab the value of the static pressure there. You can simple select the surface in a plot, select the point, and infer what the pressure is from te ranges. You could also setup monitors or reports. Usually, since you are doing 3D simulations anyway, you like to use more than just point data and get the average static pressure at plane slicing through that axial location. Note however, that it might be better to calculate the total pressure drop rather than the static pressure drop depending on you problem setup. Last edited by LuckyTran; June 5, 2017 at 18:09. |
|
June 5, 2017, 01:36 |
|
#5 |
Senior Member
Kal-El
Join Date: Apr 2017
Location: Finland
Posts: 150
Rep Power: 9 |
I would monitor the average pressure in those planes.
|
|
June 5, 2017, 04:51 |
|
#6 |
New Member
Join Date: May 2017
Posts: 8
Rep Power: 8 |
||
June 5, 2017, 05:08 |
|
#7 |
Senior Member
Kal-El
Join Date: Apr 2017
Location: Finland
Posts: 150
Rep Power: 9 |
Create planes:
https://www.sharcnet.ca/Software/Flu...g/node1120.htm Monitor average pressure on those planes: http://www.afs.enea.it/project/neptu...ug/node815.htm As LuckyTran said, total pressure might be better than static pressure. |
|
June 5, 2017, 11:45 |
|
#8 | |
New Member
Join Date: May 2017
Posts: 8
Rep Power: 8 |
Quote:
|
||
June 7, 2017, 03:59 |
|
#9 | |
New Member
Join Date: May 2017
Posts: 8
Rep Power: 8 |
Quote:
As for the 'Report Type', which one do I choose? Mass Weighted Average or Area Weighted Average? After I run the calculation, I just have to go to Reports>Surface Integrals to compute the average pressure, right? |
||
June 7, 2017, 04:10 |
|
#10 | ||
Senior Member
Kal-El
Join Date: Apr 2017
Location: Finland
Posts: 150
Rep Power: 9 |
Quote:
Quote:
https://www.sharcnet.ca/Software/Flu...g/node1050.htm |
|||
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
dsmcInitialise - dsmcFoam | archymedes | OpenFOAM Pre-Processing | 94 | July 15, 2016 16:14 |
Pressure Outlet Guage pressure | Mohsin | FLUENT | 36 | April 29, 2016 17:16 |
Pressure pulsation in a pipe due to sudden opening | asder | CFX | 3 | March 2, 2008 17:18 |
Terrible Mistake In Fluid Dynamics History | Abhi | Main CFD Forum | 12 | July 8, 2002 09:11 |
Hydrostatic pressure in 2-phase flow modeling (long) | DS & HB | Main CFD Forum | 0 | January 8, 2000 15:00 |