Modeling hydrogen/air in an open-roofed enclosure

_rob · February 14, 2018, 11:35

Hello everyone,

I'm working on modeling the flow of hydrogen through still air in an open-roofed 9x10 ft enclosure in Fluent (would CFX be better for this?). From what I've read online, I need to enable gravity and possibly use the Boussinesq approximations. I'm new to Fluent and CFD in general, and I've been trying to climb the learning curve on my own, but it's tough. If anyone could give me some pointers or direct me to a relevant tutorial to make the climb easier, I would greatly appreciate it.

Thanks!

_rob · February 15, 2018, 09:57

A couple specific questions:

1. The tutorials I've seen model a round pipe as a single solid body, name the planar faces of the body as inlet and outlet, and the software figures out that the pipe is hollow, how to mesh accordingly, and which direction to flow. But what if I have a 9 ft x 9 ft enclosure with a 1/2" diameter source of hydrogen somewhere at the bottom? Do I model a small solid cylinder at the bottom of a solid cube and label the planar face of the cylinder as the inlet? How do I specify that the enclosure is filled with stationary air and the pipe is only releasing hydrogen?

2. Should I use the Volume of Fluids model, the Multiphase model, or something else?

_rob · February 15, 2018, 11:35

An image of what I'm trying to do is shown below. Basically, I have an open 9 ft^3 enclosure with a 5" high floor vent at normal lab conditions. A hydrogen source is somewhere on the bottom of the enclosure, and the top is either fully open with no roof or has a cover with a hole in it. I want to model the path hydrogen takes to escape the enclosure.

February 14, 2018, 11:35	Modeling hydrogen/air in an open-roofed enclosure	#1
_rob New Member Robert Join Date: Feb 2018 Posts: 3 Rep Power: 8	Hello everyone, I'm working on modeling the flow of hydrogen through still air in an open-roofed 9x10 ft enclosure in Fluent (would CFX be better for this?). From what I've read online, I need to enable gravity and possibly use the Boussinesq approximations. I'm new to Fluent and CFD in general, and I've been trying to climb the learning curve on my own, but it's tough. If anyone could give me some pointers or direct me to a relevant tutorial to make the climb easier, I would greatly appreciate it. Thanks!

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Custom Thermophysical Properties	wsmith02	OpenFOAM	4	June 1, 2023 14:30
[swak4Foam] swak4foam for OpenFOAM 4.0	mnikku	OpenFOAM Community Contributions	80	May 17, 2022 08:06
Trouble compiling utilities using source-built OpenFOAM	Artur	OpenFOAM Programming & Development	14	October 29, 2013 10:59
centOS 5.6 : paraFoam not working	yossi	OpenFOAM Installation	2	October 9, 2013 01:41
modeling open air conditions	Balaji	FLUENT	2	November 14, 2004 11:10

February 15, 2018, 09:57		#2
_rob New Member Robert Join Date: Feb 2018 Posts: 3 Rep Power: 8	A couple specific questions: 1. The tutorials I've seen model a round pipe as a single solid body, name the planar faces of the body as inlet and outlet, and the software figures out that the pipe is hollow, how to mesh accordingly, and which direction to flow. But what if I have a 9 ft x 9 ft enclosure with a 1/2" diameter source of hydrogen somewhere at the bottom? Do I model a small solid cylinder at the bottom of a solid cube and label the planar face of the cylinder as the inlet? How do I specify that the enclosure is filled with stationary air and the pipe is only releasing hydrogen? 2. Should I use the Volume of Fluids model, the Multiphase model, or something else?

February 15, 2018, 11:35		#3
_rob New Member Robert Join Date: Feb 2018 Posts: 3 Rep Power: 8	An image of what I'm trying to do is shown below. Basically, I have an open 9 ft^3 enclosure with a 5" high floor vent at normal lab conditions. A hydrogen source is somewhere on the bottom of the enclosure, and the top is either fully open with no roof or has a cover with a hole in it. I want to model the path hydrogen takes to escape the enclosure.