Enclosure error

b.val · May 11, 2018, 13:08

Hello all,

I have to create a rocket composed by fins and a nose printed on 3D for classe. Unfortunately, I must make a simulation on ANSYS Fluent but I'm stuck in the very begining to create the Enclosure. The following message appears :

"Error: Boolean operation failed
Context: Geometry Engine, while generating Feature Enclosure1

Warning: At least one of the imported/attached/converted bodies could not be validated. It is possible that subsequent modeling operations will fail.
Additional information: The following could not be validated: bouteillev2.prt
Context: Feature Enclosure1"

I tryed a lot of different things but nothing worked. Could you please help me to fix my issue ?

There is the link to download my project with all its creo parts.
http://www.mediafire.com/file/7ccqn6...oject%20S4.zip

Thank you.

moh_zain · May 11, 2018, 14:19

Hi I use old version of fluent your file was not open with me but I think the problem is in the drawing file
send me picture

b.val · May 11, 2018, 16:14

Hello, thank you for helping me.
There is my drawing file from Creo PTC. (.drw)

http://www.mediafire.com/file/t37xfv.../drw0001.drw.1

Or the same but in .pdf

http://www.mediafire.com/file/ls53vn...4/_8d8lrop.pdf

moh_zain · May 15, 2018, 16:09

HI I saw the drawing I think their is small problem ( may be some surface not converted to body ) but you need to check is body bouteillev2 because the massage name it so check it

May 11, 2018, 13:08	Enclosure error	#1
b.val New Member Join Date: May 2018 Posts: 2 Rep Power: 0	Hello all, I have to create a rocket composed by fins and a nose printed on 3D for classe. Unfortunately, I must make a simulation on ANSYS Fluent but I'm stuck in the very begining to create the Enclosure. The following message appears : "Error: Boolean operation failed Context: Geometry Engine, while generating Feature Enclosure1 Warning: At least one of the imported/attached/converted bodies could not be validated. It is possible that subsequent modeling operations will fail. Additional information: The following could not be validated: bouteillev2.prt Context: Feature Enclosure1" I tryed a lot of different things but nothing worked. Could you please help me to fix my issue ? There is the link to download my project with all its creo parts. http://www.mediafire.com/file/7ccqn6...oject%20S4.zip Thank you.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[blockMesh] blockMesh with double grading.	spwater	OpenFOAM Meshing & Mesh Conversion	92	January 12, 2019 09:00
[swak4Foam] GroovyBC the dynamic cousin of funkySetFields that lives on the suburb of the mesh	gschaider	OpenFOAM Community Contributions	300	October 29, 2014 18:00
OpenFOAM without MPI	kokizzu	OpenFOAM Installation	4	May 26, 2014 09:17
Installation OF1.5-dev	ttdtud	OpenFOAM Installation	46	May 5, 2009 02:32
DecomposePar links against liblamso0 with OpenMPI	jens_klostermann	OpenFOAM Bugs	11	June 28, 2007 17:51

May 11, 2018, 14:19		#2
moh_zain Member mohamed Join Date: Apr 2016 Posts: 34 Rep Power: 10	Hi I use old version of fluent your file was not open with me but I think the problem is in the drawing file send me picture

May 11, 2018, 16:14		#3
b.val New Member Join Date: May 2018 Posts: 2 Rep Power: 0	Hello, thank you for helping me. There is my drawing file from Creo PTC. (.drw) http://www.mediafire.com/file/t37xfv.../drw0001.drw.1 Or the same but in .pdf http://www.mediafire.com/file/ls53vn...4/_8d8lrop.pdf

May 15, 2018, 16:09		#4
moh_zain Member mohamed Join Date: Apr 2016 Posts: 34 Rep Power: 10	HI I saw the drawing I think their is small problem ( may be some surface not converted to body ) but you need to check is body bouteillev2 because the massage name it so check it